Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 379 / 549 Prev Next

Dmc door board

Last post by Pjf79, 3 weeks ago

Posts: 28

Having issues where doors stop working in both the...

By beaupeep 11 years ago
Are you getting door faults? Like a 309 phasing fa...

By Indirtwet... 10 years ago
Nope, it won't let me save

By beaupeep 10 years ago
Did you resolve the problem?

By Elevatort... 10 years ago
view all posts

Garaventa Inclined Wheelchair Lift Cat5 Test

Last post by Pjf79, 3 weeks ago

Posts: 6

Does Anyone have a write up or manual for cat5 ful...

By ABE 11 years ago
I was actually looking for unit specific info on h...

By ABE 11 years ago
You should be able to get that info from Garaventa...

By solidstat... 11 years ago
In my experience unit specific info is hard to com...

By tjb 11 years ago
view all posts

Tac 20/ dover

Last post by Pjf79, 3 weeks ago

Posts: 7

Is there any way to shut off the twin post telesco...

By beaupeep 11 years ago
Those Sensors are very touchy. Have to be right on...

By Rolly 11 years ago
I know that the static sensors I/Os can be deleted...

By Indirtwet... 11 years ago
They can be jumped i believe. If need be

By Whadafack 10 years ago
view all posts

Schindler 400a

Last post by Pjf79, 3 weeks ago

Posts: 1

I have a t3 fault that's always coming in near the...

By beaupeep 11 years ago

tac32

Last post by Pjf79, 3 weeks ago

Posts: 5

Can anyone tell me if the tac32 is fully nonpropri...

By grasshopp... 11 years ago
Thanks

By grasshopp... 11 years ago
Try to trouble shoot CAN with the UIT tool.

By Street ro... 10 years ago
I have seen a lot of these where the uit is frozen...

By elevatorp... 10 years ago
view all posts

e411 learn run error NRZ.

Last post by Pjf79, 3 weeks ago

Posts: 7

Hi all. Having a problem with an "NRZ out of range...

By tjb 11 years ago
the tool just says "NRZ out of range" I dont see a...

By tjb 11 years ago
1 1/16 away from DZ is normally pretty close. At t...

By NewMech 11 years ago
Thank you NewMech. Any help is greatly appreciated...

By tjb 11 years ago
view all posts

kone kcm831 problem

Last post by Pjf79, 3 weeks ago

Posts: 12

have a 3 car group of traction mrl's building shut...

By Vatorgato... 11 years ago
Its oil and grease account. I have very limted kno...

By Vatorgato... 10 years ago
U could try swapping those gateways boards for dif...

By lowoil 10 years ago
The PI showing 16 is the clue. You have lost some ...

By koneislan... 10 years ago
view all posts

330a

Last post by Pjf79, 3 weeks ago

Posts: 3

It started with, "We are having power problems in ...

By jkh 11 years ago
might not be same, recently had intrmitten problem...

By Boa 11 years ago
Jkh, the R 176 is the resistor near the door power...

By cucuvator 11 years ago

mph hand held

Last post by Pjf79, 3 weeks ago

Posts: 5

Is there a way to reset the old schindler (mph) ha...

By Ken1 11 years ago
Thanks, any idea where i can find the hht software...

By Ken1 11 years ago
PM me an email address!

By Rolly 11 years ago
You can buy one from ECI.

By E-man 11 years ago
view all posts

Otis 411, what is GS_P

Last post by Pjf79, 3 weeks ago

Posts: 4

I seem to be having an intermittent problem with t...

By Detroit C... 11 years ago
Is this the same car you ask about BP? If it is, s...

By jkh 11 years ago
That's the gate switch PAL input. It's one of the ...

By Magic smo... 11 years ago
car is running, I believe the problem was DCL cont...

By Detroit C... 11 years ago

Page 379 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
57 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed