Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 356 / 549 Prev Next

MPH-2 PROBLEM

Last post by Pjf79, 3 weeks ago

Posts: 22

I'm hoping someone can shed a little light on an i...

By CES 10 years ago
Not at the top...Not at the bottom..

By E-man 10 years ago
somewhere in between

By Vatorgato... 10 years ago
I'm not sure I want to LIMIT myself with a one wor...

By jkh 10 years ago
view all posts

Dover composite problems.

Last post by Pjf79, 3 weeks ago

Posts: 6

I Just took on some Dover composites. Bad shape. I...

By Sam C L 10 years ago
Replaced selector guides.

By Sam C L 10 years ago
Not sure how compounding effecfs this...the elevat...

By Sam C L 10 years ago
Have you checked your generator brushes this can c...

By Elevatorj... 10 years ago
view all posts

Dover MP1

Last post by Pjf79, 3 weeks ago

Posts: 3

have an MP1 that is firing the open I/O only at th...

By Sammy 10 years ago
do you have access to new cards? The IFA card cont...

By pdq1600 10 years ago
Think we got it. Embarrassing, but it was the bott...

By Sammy 10 years ago

Northern TKE Velino escalator

Last post by Pjf79, 3 weeks ago

Posts: 3

I'm getting a fault 48, which is is used on tandem...

By Rick 10 years ago
Just out of curiosity...What is a 48 fault?

By elmcannic 10 years ago
is northern different than dover/tk velino? my lis...

By up_n_down 10 years ago

garavanta artira

Last post by Pjf79, 3 weeks ago

Posts: 8

need help with a drive fault on a artira. Im sure ...

By The-pope 10 years ago
When you do an MLR, do the hall buttons flash in a...

By Johnny 10 years ago
check for continuity between the steel cable and t...

By Sammy 10 years ago
ok i will try that thanks.

By The-pope 10 years ago
view all posts

Motion 4000

Last post by Pjf79, 3 weeks ago

Posts: 3

Hie guys can someone assist lm resuscitating a lif...

By encoder45 10 years ago
MPI-A,Have you tried the board reset?GS,Is DPM pic...

By jkh 10 years ago
You will get the GS input failure if the controlle...

By InFritzWe... 10 years ago

diagnostic tools

Last post by Pjf79, 3 weeks ago

Posts: 4

Has anyone been using the diagnostic software that...

By ubro96 10 years ago
I've seen the World Tool for the DMC, it's good.

By E-man 10 years ago
The IMS software on a Dell laptop with the needed ...

By EasternES... 10 years ago
Looking for a laptop loaded with interface softwar...

By west 10 years ago

Kone ST

Last post by Pjf79, 3 weeks ago

Posts: 3

Just took over a ST in a hospital on November 1 an...

By DripCan 10 years ago
Check your traveling cable wires, car communicatio...

By E-man 10 years ago
Almost 100% it is the tach wheel, replace it, and ...

By NYTECH 10 years ago

Elevator boneyard? ISO overspeed brake Cheney vpl

Last post by Pjf79, 3 weeks ago

Posts: 4

Is there anyone who has an elevator scrapyard/bone...

By wagvan 10 years ago
How did this fail? Are you a elevator contractor o...

By ABE 10 years ago
No, I am the Pastor of the church it is installed ...

By wagvan 10 years ago
God gave you judgement and wisdom. Please use it t...

By Robert Kr... 10 years ago

400A Security

Last post by Pjf79, 3 weeks ago

Posts: 7

We picked up this 400A duplex about a year ago. Th...

By Indirtwet... 10 years ago
Thank you

By Indirtwet... 10 years ago
Did that work?

By JustWolf 10 years ago
I haven't got back there yet, maybe tomorrow. I wa...

By Indirtwet... 10 years ago
view all posts

Page 356 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
1 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed