Elevator Forum

Tac 20 universal do...
 
Notifications
Clear all

Tac 20 universal door control board

18 Posts
6 Users
0 Reactions
15.8 K Views
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter   [#25749]
Had a flood. Water damage to universal door control board on top of car. Is this board a drop in replacement? Will I have to do any programming with IMS on the new board ?



   
Quote
(@upanddown2321)
Trusted Member
Joined: 17 years ago
Posts: 96

   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776

   
ReplyQuote
(@huskervator)
Eminent Member
Joined: 17 years ago
Posts: 37
 
the website has a list of operators with setup instructions. You can download one that fits your needs. You will need software based on your door configuration. If you have a operator with a UIT I have swapped boards, the software is retained and a few parameters and your in business. If it's a operator without UIT you will need IMS and software.



   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776

   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759
 
Order a NEW door board, should be a 6300PA6, a 6300HL1 UIT and the 6” ribbon cable part #9863295. You can do it without the ribbon cable but it makes it a lot easier. The NEW door board will come with V2R24 generic software and has the profiles already loaded and accessible through a new menu called Config or something like that. So you can just plug it in, pick the right profile from the UIT, save to flash, do an autonull and a scan, turn it off, pull the UIT and keep it for the next time. You should be in business.



   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter  
They gave me part number 980377 door operator board. This is the board that fits the motor . There is no UIT



   
ReplyQuote
(@upanddown2321)
Trusted Member
Joined: 17 years ago
Posts: 96
 
When you order the board you would order the UIT seperate.I would get it since the door operator UIT can be used from job to job, easier to carry than a laptop.



   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter  
I tried to do it with out the UIT . But my ims would not get into the door diagnostics smart fast . It said only DMC II .
So I ordered the UIT. will I be able to do everything from the UIT interface ?



   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729
 
If you have IMS and it was installed correctly there should be an icon on desktop called UDC Fast. You use a Thyssen (RS-485) Orange cable to plug into board on top of car. You must also change the serial port driver to ACPI before trying to connect to door board.



   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759
 
I think it does say DMC-II. It kind of is. I think that’s what the Tac20 was going to be called before Thyssen bought Dover. But you can do everything from the UIT.



   
ReplyQuote
(@whadafack)
Trusted Member
Joined: 17 years ago
Posts: 80

   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759

   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter  
Vertical express send me the ribbon cable only. No UIT . Now they tell me UIT interface takes months to ship .



   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759

   
ReplyQuote
Page 1 / 2
Share:
Scroll to Top