Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 302 / 549 Prev Next

ThyssenKrupp LEV Electrical Problem

Last post by Pjf79, 3 weeks ago

Posts: 5

Hi, I have a LEV elevator. I live 120 miles from t...

By Boomer_AZ 9 years ago
The house panel breaker isn’t tripped. There is a ...

By Boomer_AZ 9 years ago
The 120VAC for the car lighting does not use the U...

By Johnny 9 years ago
Johnny, I am fairly sure I am looking at the corre...

By Boomer_AZ 9 years ago
view all posts

Schindler 330a Hall Buttons to keyed

Last post by Pjf79, 3 weeks ago

Posts: 3

Anyone have a simple way to install on/off key swi...

By elevatorg... 9 years ago
Pm me your email. I'll send you some info

By Huskervat... 9 years ago
The bottom of the hall callboard should have a bla...

By KSNY 9 years ago

Do vacuum tube logic elevator controllers exist?

Last post by Pjf79, 3 weeks ago

Posts: 5

Most older elevators (c. 1979 or earlier) were bui...

By UADA 9 years ago
Originally Posted by Johnny Otis used rectifer tub...

By UADA 9 years ago
yeah and a real mongrel when they played up in hum...

By kiwinight... 9 years ago
If you ever have the chance to see the original ad...

By Johnny 9 years ago
view all posts

DAA26800Y1-LF Kone

Last post by Pjf79, 3 weeks ago

Posts: 1

Hello,I have replaced escalator PCB P/N:DAA26800Y1...

By SV-Elevat... 9 years ago

UDC board not counting for learn run

Last post by Pjf79, 3 weeks ago

Posts: 4

we recently had to replace a water damaged Udc pa2...

By Len 9 years ago
Do you have the correct 500 ppr digital encoder? (...

By Indirtwet... 9 years ago
..........yes it was a running car until it got hi...

By Len 9 years ago
Are you just reading voltage to the Encoder or rea...

By Indirtwet... 9 years ago

Otis E335M. 1997

Last post by Pjf79, 3 weeks ago

Posts: 5

Hi guys. Got a Otis E335M keeps stopping short on ...

By Jluff 9 years ago
You should have ocss. Make sure your plugged I int...

By Kevin83 9 years ago
We dont have a lot of those controllers in my neck...

By Kevin83 9 years ago
You would better check the encoder cable 's interf...

By INTENTEC-... 9 years ago
view all posts

Otis underslung

Last post by Pjf79, 3 weeks ago

Posts: 2

We are shortening belts on an Otis under-slung car...

By danzeitz 9 years ago
Its been a few years but...... I believe we used r...

By Kevin83 9 years ago

Miprom HS. Door issues

Last post by Pjf79, 3 weeks ago

Posts: 17

Hello everybody. Long time reader. 1st time poster...

By Jblack83 9 years ago
These are door faults 49 took too long to close, 8...

By john jay 9 years ago
Thank you so much. At present the elevator is stil...

By Jblack83 9 years ago
Make sure the magnets are polarized correctly if y...

By john jay 9 years ago
view all posts

400a manual

Last post by Pjf79, 3 weeks ago

Posts: 4

I just inherited some 400a’s and I know nothing ab...

By Wispaflex... 9 years ago
pm an e-mail

By JustWolf 9 years ago
Not to go on a rant, 400A with SDM present for it'...

By JustWolf 9 years ago
if the SRM was not disabled then it can be done re...

By Tamperpru... 9 years ago

Damage six pack igbt TAC50

Last post by Pjf79, 3 weeks ago

Posts: 7

Hi Friends i'm changed 3 times the igbt six pack m...

By djenergy 9 years ago
Of course!

By grasshopp... 9 years ago
It’s worth repeating!

By Indirtwet... 9 years ago
I just had this issue where I replaced an IGBT and...

By Bilbobobb... 1 year ago
view all posts

Page 302 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
11 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed