Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 262 / 549 Prev Next

T3 CD Issue

Last post by Pjf79, 3 weeks ago

Posts: 4

I'm having a close door issue with a T3. The attac...

By wltr00 7 years ago
So you replaced PMI module 38 on PMI card #1? Did ...

By Indirtwet... 7 years ago
Make sure you used the correct module as well ther...

By boomer 7 years ago
Do you have power at OD 21/21? If not, pico fuse o...

By Johnny 7 years ago

Dover 1980’s Print

Last post by Pjf79, 3 weeks ago

Posts: 22

Does anyone has any manual or print similar to thi...

By M2RE 7 years ago
The picture is a Westinghouse relay logic 4 landin...

By Huskervat... 6 years ago
Thank you. I don't see a metal tag except for the ...

By Eleventh ... 6 years ago
Ya, I second that. The prints will cost you but no...

By Indirtwet... 6 years ago
view all posts

Ibox mce

Last post by Pjf79, 3 weeks ago

Posts: 6

Hey there wondering if any one has any thoughts on...

By Kone66 8 years ago
I didn’t check for ac but I will ,and also on the ...

By Kone66 8 years ago
Page 6-71 in the 15 Release manual has the boot se...

By UpandDown... 7 years ago
I had a similar issue and I started removing I/o b...

By Turbo6 7 years ago
view all posts

Miprom 21 A/C in overhead

Last post by Pjf79, 3 weeks ago

Posts: 12

I have a 4 car low rise geared group, very often t...

By Turbo6 8 years ago
Thanks fellas, I’m going to try the weight issue a...

By Turbo6 7 years ago
Adding weight to the car top may sound like a quic...

By john jay 7 years ago
I tend to agree with John Jay, never liked the ide...

By Indirtwet... 7 years ago
view all posts

TKE Service Tool

Last post by Pjf79, 3 weeks ago

Posts: 2

Where can I purchase a full blown TKE Service tool...

By wltr00 8 years ago
World electronics

By ashley 8 years ago

Miprom 21 hall call issue

Last post by Pjf79, 3 weeks ago

Posts: 20

I have a miprom 21 2 car group. When one of the ca...

By Bricker 8 years ago
Did you check the binary counting i/o's with the c...

By john jay 7 years ago
If the LEDs light but you don’t see the input chan...

By Indirtwet... 7 years ago
Mmogomlb, that works great on a Miprom 21

By Jcjphoeni... 7 years ago
view all posts

Mac 104 board

Last post by Pjf79, 3 weeks ago

Posts: 6

Have an issue with a 104 Mac upgrade to a door op ...

By Kone66 8 years ago
Thanks for the help/ I went over and looked at it ...

By Kone66 8 years ago
I had an issue with a Mac 104 before that was caus...

By Goat 8 years ago
Holy hell

By Philly 8 years ago
view all posts

Reliable Elevator

Last post by Pjf79, 3 weeks ago

Posts: 3

I've got an old Reliable Elevator acting up. Had a...

By wltr00 8 years ago
What type control ? Relay type? How old ?The contr...

By Seco2000 8 years ago
Prior to the fuse blowing, it never went to four b...

By elmcannic 8 years ago

Tac manuals

Last post by Pjf79, 3 weeks ago

Posts: 11

Hey there.Has anyone got manuals for the tac 32 an...

By Pace33 8 years ago
Like I said. Good for a week.

By xxXBlazeX... 7 years ago
I wish i would of saw this sooner

By DowntownL... 7 years ago
PM me what you need.

By xxXBlazeX... 7 years ago
view all posts

Dover Composite Issue

Last post by Pjf79, 3 weeks ago

Posts: 6

I've got a Composite with the Stop Switch in and o...

By wltr00 8 years ago
Got prints??? From A2 thru BR 7-1 thru Gen Shunt f...

By Johnny 8 years ago
Back contacts on BR not allowing proper operation ...

By NewMech 8 years ago
I know this is a long shot, but is the MG set spin...

By TC7 8 years ago
view all posts

Page 262 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
2 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed