Elevator Forum

Notifications
Clear all

Dover Composite

29 Posts
20 Users
0 Reactions
54.3 K Views
(@dripcan)
Estimable Member
Joined: 17 years ago
Posts: 131
Topic starter   [#14077]
Have 12stop duplex that I will get a call that car stuck at floor not responding get there an running checked door locks all floors an gate also dcl an dol all good .Left there today couple hours later called back said car at 1 doors closed not responding customer said hall button will call other car.So we're do I even start if running in morning an no fault timers or selector LEDs on



   
Quote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
20 years ago this was our everyday world. You have to play detective and eliminate problem areas from your thinking one by one. A lot of times when a Dover was stuck at a floor it would be from what we called a CS lockup. The CS relay should pulse in and out, but things like a door lock bouncing would cause it to pull in and stay energized. You may want to look at that circuit closely. Also if you have worn leveling rings on the selector it can create problems. A wire relay checker from SEES was also an invaluable tool for checking out Dover Relays. When you pull a relay out be sure to wiggle it from side to side and not up and down, this causes the base pins to get bent. Good Luck.

Last edited by john jay; 05/04/15 11:01 PM. Reason: not complete


   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798

   
ReplyQuote
 jkh
(@jkh)
Prominent Member
Joined: 17 years ago
Posts: 904
 
I once received a call for the elevator broke down at dusk. Of course they didn't want to pay for over time. The next morning we arrive and the elevator was running. At the end of the next day, (you guessed it) the elevator went down at dusk.
What we found was when the new outside lights went on at night, the voltage dropped enough to shut the elevator down.

Sometimes you have to look outside (no pun intended) of the elevator system.



   
ReplyQuote
(@newmech)
Estimable Member
Joined: 17 years ago
Posts: 203

   
ReplyQuote
(@kiwinightstalker)
Estimable Member
Joined: 17 years ago
Posts: 145

   
ReplyQuote
 E311
(@e311)
Reputable Member
Joined: 17 years ago
Posts: 363
 
It is sad when you think about it, this was our everyday at one time, has that much time passed??? It seems to have! The CS lockup, worn selector guides and slider switches, may want to check the selector "traveling cable", and of course those pesky IBM relays with the plastic coil liners that like to get brittle and brake, then the peices fall off into the relay contacts...



   
ReplyQuote
 iggy
(@iggy)
Eminent Member
Joined: 17 years ago
Posts: 23

   
ReplyQuote
(@christycollett)
Honorable Member
Joined: 17 years ago
Posts: 420
 
Hey you Guys your hurting my feelings by recommending a relay tester from SEEs. How bout WizBang Mark V designed and built by a fellow IUEC member?

I have the CS Lock-up band-aid if you want it

Work Safe,

Jim [email protected]



   
ReplyQuote
(@dripcan)
Estimable Member
Joined: 17 years ago
Posts: 131
Topic starter  
ok had FT faulted out borrowed tester an found only one contact in CS working replaced an no calls as of now. Christy I will be contacting you because I got a told about control of live electrical source.Cant use SEES tool with power off.

Last edited by DripCan; 05/05/15 08:50 PM.


   
ReplyQuote
(@danzeitz)
Prominent Member
Joined: 17 years ago
Posts: 672

   
ReplyQuote
(@dkwoodham)
Active Member
Joined: 17 years ago
Posts: 5

   
ReplyQuote
 jkh
(@jkh)
Prominent Member
Joined: 17 years ago
Posts: 904

   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729
 
Is the car at floor level when you find it? Had one of these once that slipped traction on a zoning stop because brush did not provide enough slow down distance and CS lock-up occurred between floors.



   
ReplyQuote
 TC7
(@tc7)
Trusted Member
Joined: 17 years ago
Posts: 71
 
I thing to try is rig MGT to not time out for trouble shooting purposes . Maybe MG set times out and doesn't restart. I believe the timer fires to time out MG set. Also 12A timer and auxiliaries on motor starting contactor if wye delta start. Sometimes all you have is process of elimination.



   
ReplyQuote
Page 1 / 2
Share:
Scroll to Top