Elevator Forum

Swift futura proble...
 
Notifications
Clear all

Swift futura problems

32 Posts
14 Users
0 Reactions
52 K Views
(@scarz3)
Eminent Member
Joined: 17 years ago
Posts: 14
Topic starter   [#20933]
Hi all.

Been having problems with a couple of swift futura units.

Usually they run fine for anything between 1 hour to 3 days, and then they break down.
Usually getting faults 9 & 10, and usually crashes out on fault 18. Although other faults have been appearing.
Modules and contactors have been changed. DPP switches have been changed.
Drive, encoder, brake board have all been swapped with known working ones.

Also on our DPP switches we're reading between 3.0 and 3.4 volts on DPP2 depending on adjustments made and nothing seems to get it down to the correct voltage.

We just can't seem to get to the bottom of this.

Any help would be much appreciated.



   
Quote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
 
Check the SCRs. Usually on the back of the controllers. I think any high readings between pairs around 19-20ohms or higher means they need to b replaced



   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776

   
ReplyQuote
(@elmcannic)
Honorable Member
Joined: 17 years ago
Posts: 635
 
Sounds like you've eliminated a number of possibilities.
What type of contactor or contactors are being used? The late 1990's Futuras used a pair of loop contactors with huge micro switches under the coil. Problematic design. Faults 18 & 94 you get about every time a recovery has initiated.
Does this job use the RVU Wizard thing? If so, you can set the system to capture just about any fault then playback the screen and watch all inputs before the fault occurred... great tool. Are the ropes sliding on the sheaves maybe?
And lastly, has the building put any antennae or satellite dishes and their associated cabling near the machine room? Ask me how I know about this one! No wait...don't!



   
ReplyQuote
(@scarz3)
Eminent Member
Joined: 17 years ago
Posts: 14

   
ReplyQuote
(@scarz3)
Eminent Member
Joined: 17 years ago
Posts: 14
Topic starter  
Contactors are all Schneider. No satellite dishes positioned near any of our equipment. Will have a go at using the playback tool on the wizard. Thanks



   
ReplyQuote
(@scarz3)
Eminent Member
Joined: 17 years ago
Posts: 14
Topic starter  
Ok, used the frame playback, when the lift crashes, we get fault 94 and 24 in the same frame, and we also lose EMSD. Nothing else drops out.
Does this indicate anything other than the drive?



   
ReplyQuote
(@elmcannic)
Honorable Member
Joined: 17 years ago
Posts: 635

   
ReplyQuote
(@scarz3)
Eminent Member
Joined: 17 years ago
Posts: 14

   
ReplyQuote
 jkh
(@jkh)
Prominent Member
Joined: 17 years ago
Posts: 904
 
Scarz3,
The common denominator of 24 and 94 errors is your encoder. PM your email address. I have a few things I can share.



   
ReplyQuote
 jkh
(@jkh)
Prominent Member
Joined: 17 years ago
Posts: 904
 
Scarz3,
The common denominator of 24 and 94 errors is your encoder. PM your email address. I have a few things I can share.



   
ReplyQuote
(@jcjphoenix)
Reputable Member
Joined: 17 years ago
Posts: 239
 
I had same faults occuring on a swift 5000 with a magnetec dsd 412 drive. I did everything you've tried if not more trying to fix it. The conduit for the velocity Encoder wiring was grounded and the shield was grounded on one side like it should be. I started out by pulling the wiring out of the conduit, temporarily running it out of the bottom of the drive across the floor to the encoder so I knew it was far away from any other circuits that could create noise in the line. The problem went away and I'm fairly sure the noise was from the way the wiring was ran from the bottom of the drive to the top of the controller.



   
ReplyQuote
(@notime)
Reputable Member
Joined: 17 years ago
Posts: 197

   
ReplyQuote
(@scarz3)
Eminent Member
Joined: 17 years ago
Posts: 14

   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798

   
ReplyQuote
Page 1 / 3
Share:
Scroll to Top