Elevator Forum

Notifications
Clear all

Miprom 21

28 Posts
7 Users
0 Reactions
52.4 K Views
(@j-sand)
Estimable Member
Joined: 17 years ago
Posts: 100
 
The speed board would not be coming in until 267 fpm?, We are "flat-topping" at 200 fpm. MSU and Drive PPR are both at 2048, now and before the problem. The encoder is mounted directly to the shaft of the armature. 150 fpm speed board is coming in correctly on AUTO. This speed difference occurs on AUTO as well as inspection speed (now at 40 fpm, or 10% of contract so I don't have to do math), so the speed boards wouldn't be a factor at that low.

Last edited by J Sand; 04/05/15 07:09 PM.


   
ReplyQuote
(@j-sand)
Estimable Member
Joined: 17 years ago
Posts: 100

   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
Go to MSU adjust, 2nd screen will tell you what is limiting you. If you have load weighing voltage over 100% it will limit you to half of Mvel. Mvel should be at contract speed. Also if you have alternate profile software and your EPC input is high that will also limit your speed. Another quick thing is to replace your MSU Board, they are plug and play.



   
ReplyQuote
(@notime)
Reputable Member
Joined: 17 years ago
Posts: 197
 
Check the MOtion Info all Screen maibe is not a Fault is just a Status Somithing activated "earthquake" Loadweight" etc......



   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798

   
ReplyQuote
(@j-sand)
Estimable Member
Joined: 17 years ago
Posts: 100
 
But all of the things here are based on AUTO, even runs slow on inspection though. I will try tomorrow. So far, no faults, dispatch is normal, EPC is good, Load is at 0%. Nothing to show alt profile. It did run 75% speed for a short time Friday but then back to 50%. Keep you all posted



   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
A couple of Drive Parameters to check are, 621 feed back device, 558 ME base speed, 606 Motor Base speed, and 607 and 608 speed limits.



   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798

   
ReplyQuote
(@j-sand)
Estimable Member
Joined: 17 years ago
Posts: 100
 
yep, 621 =0 for encoder, base speeds are 1150 and speed limits are 1217. mvel-400. trying to get route mech to swap drive logic boards but customer is "very animated" about turning off both cars, even for 3 mins. Might have to do in middle of night.



   
ReplyQuote
(@j-sand)
Estimable Member
Joined: 17 years ago
Posts: 100

   
ReplyQuote
(@vatorgator)
Honorable Member
Joined: 17 years ago
Posts: 432
 
does motion info screen 1 give any clue it gives you command velocity, max velocity for the run you are making, and reason for any velocity limit should be some clue here as to what it is trying to do. then switch to screen 3 for feedback etc.



   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798

   
ReplyQuote
(@j-sand)
Estimable Member
Joined: 17 years ago
Posts: 100
 
both checked out ok. sent drive to access drive. LOL, now second car just loss logic board. Gotta love em. thanks guys for the help



   
ReplyQuote
Page 2 / 2
Share:
Scroll to Top