Elevator Forum

Forums
General Discussion
Technical Questions
TKE Northern 3200 w...
 
Notifications
Clear all

TKE Northern 3200 with Quantum / HPV 900 drive

 
Technical Questions
Last Post by Anonymous 6 days ago
11 Posts
1 Users
0 Reactions
21.4 K Views
RSS
 EDMAn
(@EDMAn)
Joined: 1 second ago
Posts: 0
Topic starter 28/01/2013 6:53 am   [#5651]
Wondering if anyone has run into the same problem...

I've got a couple of 3200 units that seem to stall after the M contactor picks.

High voltage board outputs MA and MB, but no P. Relay board U1 or D1, UD, SM all picked. DEN out...

Only drive signal showing on the relay board is the Drive Ready LED...

Car is always level with the floor, brake not picked, drive not energized, showing RDC low on RMS board... only odd thing is a flickering OK signal on map unit (output group 18?)...

Any thoughts? Happens every 2 - 3 weeks. Tipping a hall lock or cycling inspection will cause M to drop and car will take off...



   
Quote
 sbrmilitia
(@sbrmilitia)
Joined: 1 second ago
Posts: 0
29/01/2013 7:15 am  
Do you have a HPV 900 manual? I had these in some swift geared cars I think I still have the manual in my office somewhere.



   
ReplyQuote
 Jim
(@Jim)
Joined: 1 second ago
Posts: 0
29/01/2013 7:55 am  
flickering i/o you say. pull out the hvs 9603 board and measure all of the 4.7 micro farad capacitors. i think there is about 16 of them. replace all the bad ones.



   
ReplyQuote
 EDMAn
(@EDMAn)
Joined: 1 second ago
Posts: 0
Topic starter 29/01/2013 8:17 pm  
HVS board has already been replaced, brand new from Northern... and I do have an HPV manual.



   
ReplyQuote
 Eric
(@Eric)
Joined: 1 second ago
Posts: 0
31/01/2013 5:54 am  
hello.
#1 gearless or traction
#2 is there a speed command



   
ReplyQuote
 E311
(@E311)
Joined: 1 second ago
Posts: 0
31/01/2013 6:57 am  
One of the main issues Ive had with these is in the redundancy circuit (RE) If the contacts are not in really good shape you will get problems. If my memory serves me right its a 24vdc circuit. Also the drive contactor's aux. contacts are a known issue.



   
ReplyQuote
 EDMAn
(@EDMAn)
Joined: 1 second ago
Posts: 0
Topic starter 31/01/2013 8:06 pm  
Geared units, no speed command being issued to the drive...



   
ReplyQuote
 Luis
(@Luis)
Joined: 1 second ago
Posts: 0
31/01/2013 11:42 pm  
Problem using IMS USB

i am facing some problems concerning to the communication laptop-TAC 50-04controller using the IMS USB.

My lap top have no D-Shell 9 pins and i tried a USB to serial converter and i made the follwing configuration in the "system config" menu:

on COMMUNICATION tab: LAN Router- None, Connect- Direct
on LON tab: "Connect-SLTA", "Mode-LTA Config".

I tried other settings , but without success.

Regards



   
ReplyQuote
 Eric
(@Eric)
Joined: 1 second ago
Posts: 0
01/02/2013 6:28 am  
check the N O auxillary contacts on M contactor.

as for your tac 50-04, use usb or ether net, and you need the black IMS icon on your lap top



   
ReplyQuote
 EDMAn
(@EDMAn)
Joined: 1 second ago
Posts: 0
Topic starter 01/02/2013 8:50 am  
All contacts on the M contactor are fine... if I remember correctly, even if the NO contacts intermittently don't make, the controller would drop M... in this situation M is held electrically...

Luis.... you should start your own thread... your issue is a little unrelated to this one...



   
ReplyQuote
 Luis
(@Luis)
Joined: 1 second ago
Posts: 0
13/10/2014 3:41 am  
Thank you Eric. Now i understand the reason of the problem that i asked for help.

Is because the IMS via usb is for 32 bit TAC50. The ones i have are 16 bit.

Thank you all.



   
ReplyQuote
Forum Jump:
  Previous Topic
Next Topic  

Currently viewing this topic 1 guest.

Share:
Scroll to Top