Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 395 / 549 Prev Next

TAC 20

Last post by Pjf79, 3 weeks ago

Posts: 14

Have a TAC 20. 2 stop, twin post single stage jack...

By sec 11 years ago
"We will post our findings as we complete in the n...

By elmcannic 11 years ago
Ims will save your life over and over, check the u...

By elevatorp... 11 years ago
Speaking of viscosity, make sure the car is not cr...

By Indirtwet... 11 years ago
view all posts

Tac 20

Last post by Pjf79, 3 weeks ago

Posts: 4

Is the tapehead a straight out swap. Can anyone pm...

By beaupeep 11 years ago
On a tac 20 you need the laptop

By Elevatort... 11 years ago
No, if you have a UIT then go to Commands and issu...

By xxXBlazeX... 11 years ago
Rodney is correct, selector does not hold any info...

By Silly 11 years ago

TAC32 no door communication

Last post by Pjf79, 3 weeks ago

Posts: 14

error codes say door communication failure & d...

By Boa 11 years ago
thanks all, my first thiughts were right. door bd ...

By Boa 11 years ago
Very good.

By elmcannic 11 years ago
Yes Elm, unless the micro switch is bad on the boa...

By Silly 11 years ago
view all posts

Armor #2 geared machines

Last post by Pjf79, 3 weeks ago

Posts: 2

Does anyone have a repair or parts manual for this...

By ABE 11 years ago
I'm dealing with an ARMOR CONTROLLER , is a group ...

By Mark26 11 years ago

any mitsubishi expert here?

Last post by Pjf79, 3 weeks ago

Posts: 3

im looking for mitsubishi elevators expert that ca...

By david1988 11 years ago
Have you contacted your local Mitsubishi office?

By rac66 11 years ago
cannot use the local mitsubishi office.there is on...

By david1988 11 years ago

Tac20 188E

Last post by Pjf79, 3 weeks ago

Posts: 2

Hi,Is there any way to reprogram the I/O's. For ex...

By tmunns 11 years ago
Yes, if you have the office version of IMS you can...

By xxXBlazeX... 11 years ago

KONE KCM831 Information/Manuals

Last post by Pjf79, 3 weeks ago

Posts: 2

Any help would be greatly appreciated. I've just p...

By ernieschn... 11 years ago
PM sent.

By xxXBlazeX... 11 years ago

TAC 20

Last post by Pjf79, 3 weeks ago

Posts: 4

??Tac 20, Siemens soft start has LCD screen blank....

By chicago 11 years ago
Siemans Class 72 logic board,see the post 7/30/201...

By JustWolf 11 years ago
Yes, it looks like that. But if I don't have 110 v...

By chicago 11 years ago
Check for 120Vac on terminals 1 and 3 on the start...

By xxXBlazeX... 11 years ago

Counterweight frame

Last post by Pjf79, 3 weeks ago

Posts: 2

We are working on a modernization in an old factor...

By dre1383 11 years ago
A17.1-2013-8.7.2.22.2, states that, Rod type Count...

By john jay 11 years ago

Miprom 21 Error 38 and 22

Last post by Pjf79, 3 weeks ago

Posts: 3

One in a group has developed an issue of running f...

By BRG 11 years ago
did you try replacing the DZD relay? the little sm...

By Vatorgato... 11 years ago
Usually this happens at the top terminal landing.W...

By john jay 11 years ago

Page 395 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
10 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed