Elevator Forum

Otis LRV3 pushbutto...
 
Notifications
Clear all

Otis LRV3 pushbutton

25 Posts
10 Users
0 Reactions
63.1 K Views
(@rollaway-up)
Trusted Member
Joined: 17 years ago
Posts: 50
Topic starter   [#10672]
Had in car pushbutton not working (placing a car call) on an LRV 3. Didn't have a replacement board handy so i swapped the assembly with the adjacent rear floor pb (never used) but that didnt fix it.(the old board worked fine on the rear entrance). Car is running but will not travel to level 3 front.
Im thinking processor board? Any thoughts?

Then...

Found an identical (so it appears) hall pushbutton board in the shop and i gave that a try (why not its monday).
When i energized the controller i could smell the familiar smell of burnt resistor from the cop and now have a lifeless cpu. There is a flashing red light on the processor board and a quick check of controller fuses didnt show anything obvious. Any thoughts?



   
Quote
(@e-man)
Honorable Member
Joined: 17 years ago
Posts: 480
 
I think some PB boards have a diode and some don't. I remember an Otis guy telling me to be careful when changing them out. Sorry that's not much help but that's all I know about them.

Last edited by E-man; 05/12/14 11:34 PM.


   
ReplyQuote
(@dripcan)
Estimable Member
Joined: 17 years ago
Posts: 131
 
you probably smoked your header jumper on processor,alway swap for identical an if jumper on button board was cut,do the same an cut it.Ilearned this the hard way on a friday.



   
ReplyQuote
(@rac66)
Trusted Member
Joined: 17 years ago
Posts: 68
 
Some of those pushbutton boards have a jumper (or diode like E-man said) on them that may need to be removed, so compare the new board to the old board.

The watchdog red light is a good sign. Will the car run on inspection? Can you jump the calls directly on the COP to get the car to run? If you unplug the "new" 3 front button will the car do anything?



   
ReplyQuote
 Len
(@len)
Estimable Member
Joined: 17 years ago
Posts: 194
 
when you are dealing with an LRV3 processor board.they are very hard to come by..most Lrv3 outhere have been upgraded to the Lrv4 processor..eliminates a lot of issues...



   
ReplyQuote
(@vatorgator)
Honorable Member
Joined: 17 years ago
Posts: 432
 
you took out one of the input chips on the cpu board, this is a typical trouble call, when the board jumper is not removed. need to look carefully, it does not look like a jumper, just a long piece of hard wire, i think it is in the J3 position, maybe J4, anyway if you are lucky, the input chips are in a socket, in which case you can remove the chip and replace with a new one, i have made this repair quite a few times over the years, replacing the chip will get the car back online, sometimes it will take out a couple of chips in the same area, if they are not in dip sockets, then you will have to have it repaired, or break out your soldering gun. good luck



   
ReplyQuote
(@rollaway-up)
Trusted Member
Joined: 17 years ago
Posts: 50
Topic starter  
Guys, great information thanks.

When i compared them, the only visible difference was the diode was missing the polarity stripe, if it was a jumper, the insulation looked very similar to a diode, and i recall there was a solid jumper wire on the opposite side of the pb from the diode. It was clearly for a hall pushbutton, which has a seperate interface to the controller.

If you forget about the oopsy for a minute and go back to the beginning...
When i swapped the existing pushbutton around to see if it would work on another floor input, the 3rd landing still wouldn't latch a call, even with a different assembly. Has anyone lost a car call input before in a similar way and replaced the input chips or entire board as a fix?

Also, i have an LRV4 board in stock, whats involved with the upgrade?

Last edited by rollaway-up; 05/13/14 04:33 AM.


   
ReplyQuote
(@rac66)
Trusted Member
Joined: 17 years ago
Posts: 68
 
You could just have a bad input chip, but my fear is "the smell" you described probably fried the socket as well. You'll likely have to either swap the board or send out the one you have for repair.

The LRV4 board needs a different hall button interface board and some changes in the wiring.



   
ReplyQuote
 Len
(@len)
Estimable Member
Joined: 17 years ago
Posts: 194
 
I have upgraded them before..Hall button Interface board is not different..only thing that is added with the Lrv4 board is the updated level software..wiring changes for the type of stop switch push button verses Keyed...



   
ReplyQuote
(@uppo72)
Honorable Member
Joined: 17 years ago
Posts: 562
 
Originally Posted By: rollaway-up
Had in car pushbutton not working (placing a car call) on an LRV 3. Didn't have a replacement board handy so i swapped the assembly with the adjacent rear floor pb (never used) but that didnt fix it.(the old board worked fine on the rear entrance). Car is running but will not travel to level 3 front.
Im thinking processor board? Any thoughts?

Then...

Found an identical (so it appears) hall pushbutton board in the shop and i gave that a try (why not its monday).
When i energized the controller i could smell the familiar smell of burnt resistor from the cop and now have a lifeless cpu. There is a flashing red light on the processor board and a quick check of controller fuses didnt show anything obvious. Any thoughts?

I take this has a car pcb for serial connection to the controller? If so, then if you have swapped out the button assembly for another floor, of which should have worked(as it appeared these aren't coded for each floor), then to me the car pcb, or the controller has the issue of not latching the serial data. Either way the only real way to find this, will be start swapping boards. Now you have another issue which might take precedence. I always have a healthy cynical view on parts that aren't labelled as good from the depot. When I have these I always label them as good or bad.



   
ReplyQuote
(@rollaway-up)
Trusted Member
Joined: 17 years ago
Posts: 50
Topic starter  
Well the new cpu solved the problem, but i ended up having to replace the relay board too to get it running. Now all the hall calls are lit up and the hall button interface has all inputs and outputs high, looks like one more board should do the trick.....



   
ReplyQuote
(@bayblue)
Eminent Member
Joined: 17 years ago
Posts: 29

   
ReplyQuote
 jkh
(@jkh)
Prominent Member
Joined: 17 years ago
Posts: 904
 
Bayblue,

I enjoyed reading that old thread. And I just wanted to leave you with a quote!

"It's not easy being GREEN!"
Kermit the Frog

Last edited by jkh; 05/22/14 12:41 AM.


   
ReplyQuote
 Len
(@len)
Estimable Member
Joined: 17 years ago
Posts: 194

   
ReplyQuote
(@rollaway-up)
Trusted Member
Joined: 17 years ago
Posts: 50
Topic starter  
Yes i enjpyed that thread too! Lots of good info here.

It was taking car calls and travelling to the appropriate floors, i left it running on independent for the boys to use.

When i energize, all input and output leds light up on the hall interface board. And it doesnt latch or respond to any hall calls so i figured on the board, considering its all i have left to replace.



   
ReplyQuote
Page 1 / 2
Share:
Scroll to Top