Elevator Forum

Notifications
Clear all

MPH1

18 Posts
7 Users
0 Reactions
24 K Views
(@danzeitz)
Prominent Member
Joined: 17 years ago
Posts: 672
Topic starter   [#3085]
OK, We have a 1987 version MPH1 that if the car runs for 13 seconds we get a DS10 that stops the car in flight returns to bottom landing opens the doors and takes itself out of service till a manual reset. A year ago we had the same problem and replaced the NSP (noise suppression board)and the problem went away. When it came back we changed the NSP board and again the problem went away but for only 2 weeks. We canged the board again and again the problem goes away but this time only for one week!The original prints do not have a designation for DS10 but are manuals show it as Oil Temp over/under. So we disconnected the thermostat. And we stll have the same problem. We have changed every board we can and also the power supply. We have also removed the valve coils so no movement of the car is possable and the car still times out at 13 seconds.We then kept the motor from starting and again at 13 seconds the car shuts down. This only happens between 1 and 2 because of the floor height. From 2 to 3 and 3 to 4 the car runs fine. We know that replacing the NSP board will cure the problem but they do not last long enough to be a practice solution. Any ideas we are fresh out?????



   
Quote
 Vic
(@vic)
Honorable Member
Joined: 17 years ago
Posts: 532

   
ReplyQuote
(@selfproclaimed)
Trusted Member
Joined: 17 years ago
Posts: 52

   
ReplyQuote
(@broke-sheave)
Reputable Member
Joined: 17 years ago
Posts: 418

   
ReplyQuote
 Vic
(@vic)
Honorable Member
Joined: 17 years ago
Posts: 532
 
If you put in a motor that has a varistor temperature sensor, when the control is wired for bi-metallic, (or visa-versa), you will have problems. Change the pump motor lately? Check the motor thermal anyway.



   
ReplyQuote
(@danzeitz)
Prominent Member
Joined: 17 years ago
Posts: 672
Topic starter  
Sorry I didnt cover all the things we tried. We have jumped the motor thermal and that is not the problem. We are heading back today (Its about an hour and a half from shop) To install another NSP board and I will send the old one to a repair shop where I can find out what they are fixing to see if we can back track the problem. We have been getting them from Adams for a core and I cant find out what they are fixing.



   
ReplyQuote
(@e-man)
Honorable Member
Joined: 17 years ago
Posts: 480
 
If R18 1K resistor on the NSP PCB is open will give a DS10 Temp condition because K55 (DS38) never turns on when 5 picks. But I thought it happened immediately. There's also a C18 cap that can short and take out that resistor. The 13 seconds and why the resistor is going bad is weird.



   
ReplyQuote
(@uppo72)
Honorable Member
Joined: 17 years ago
Posts: 562
 
hey same as vic. go thru your earths(grounds) on your controller.it also sounds like a power supply issue maybe a suspect motherboard connection or solder connection.you could also be a wire from this that has a broken insulation on it.

Last edited by uppo72; 03/30/12 11:52 PM.


   
ReplyQuote
 Vic
(@vic)
Honorable Member
Joined: 17 years ago
Posts: 532

   
ReplyQuote
(@e-man)
Honorable Member
Joined: 17 years ago
Posts: 480

   
ReplyQuote
(@danzeitz)
Prominent Member
Joined: 17 years ago
Posts: 672
Topic starter  
We found the problem. We had an open resistor on the NSP board for 5 (starter picked input) so even though the car ran there must be a watch dog program that shuts the car down at 13 seconds if the 5 input is not seen. The only thing in this circute is the started coil so we are replacing it and adding noise suppression.



   
ReplyQuote
(@e-man)
Honorable Member
Joined: 17 years ago
Posts: 480
 
R18? I've seen the starter pickup and drop back out with that resistor open, which is why i said immediately in my prior post.

Last edited by E-man; 04/02/12 02:56 PM.


   
ReplyQuote
 Vic
(@vic)
Honorable Member
Joined: 17 years ago
Posts: 532

   
ReplyQuote
(@scott-davidson)
Honorable Member
Joined: 17 years ago
Posts: 402
 
hey, e-man, I have 2 different mph1 prints one that shows the k55 input with a r18 resistor in front, and one that shows no resistor. Is this noise suppression circuitry something that was added on in the field, or was it added to newer mph1 controllers in the factory, or maybe both. have looked at a lot of these controllers, and never caught that small difference in the prints. good post to learn from.



   
ReplyQuote
(@danzeitz)
Prominent Member
Joined: 17 years ago
Posts: 672
Topic starter  
The job prints we have didnt show any of the NSP connection so my guys couldnt tell where things went. So when we got prints that showed NSP connections we were better off. E-man shindler has changer that resistor from 1K ohm to a 10 ohm???? Also why it is opening stays a mystery. We disconnected the starter coil so everthing was passing thru the resistor and it didnt even get warm???? We replaced the coil and added surge protection but time will tell 1 week or 1 year who knows. When Adams tec support finally answered they said the same resistor had been opening when Otis had the job. They are checking to see how many of the 75 boards they sold last year had the same problem...



   
ReplyQuote
Page 1 / 2
Share:
Scroll to Top