Elevator Forum

Notifications
Clear all

Kone fault codes

14 Posts
5 Users
0 Reactions
54.6 K Views
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48

   
Quote
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48

   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
the fault reads as follows, ss_info lost,aux door close contacts open. I think these contacts may be on the door board, not 100% sure, I don't have a print handy. good luck



   
ReplyQuote
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48

   
ReplyQuote
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48
Topic starter  
I replaced a micro switch that makes when the door is closed but I am still getting the 45 code. It seems to be happening more frequent. From what I can tell it occurs when the LIM light on the door operator board does not go low when the door is closed. Any ideas on what to do or check? Figuring I will have to buy the service tool. What is kone using for door limits on these units?



   
ReplyQuote
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48
Topic starter  
the fault is occurring when the doors close so it certainly appears to be a contact not making. Gate switch, hw door locks are ok and the blue micro switch was just replaced. I was looking for door close contact but couldn't find them. ?????



   
ReplyQuote
(@uppo72)
Honorable Member
Joined: 17 years ago
Posts: 562
 
Not sure of the operator but most new PDO's are limitless and use an encoder for open and close limits. If there is no obvious mechanical limits it should be this type. This is why its a good idea to test things( and dynamic test them ie when door moving flick the limit) before replacing them as it might not be warrented. I would be trying to do a reprogram(reset) of the PDO and then see how you go.



   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
HS Hdro's usually, but not always used the WG Door operator, the DS7 led goes low when the doors are closed. a 45 error says that your ss info is lost, look at the ss led in the controller, it should be high. the fault says that the aux door contacts are open. so if you have a WG type operator, check WG 5, terminals 1 to 3 are the aux door contacts, they go from there down to the car panel board to TB 13 then to the connection board in the controller.



   
ReplyQuote
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48

   
ReplyQuote
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48
Topic starter  
what I found is the LIM led is staying high when the doors are closed. There is a microswitch on the car door frame that when the car door closes it makes a normally open set of contacts that energizes a relay on the door board. When this relay is energized it should drop the LIM led. I unhooked the switch and LED stays on. I am highly suspecting a faulty contact on this relay which soldered on the board. Talking to Kone Spares the door close auxiliary contacts are on this board. This board has been revised several times in an attempt to correct these auxillary contacts not holding up. Going to try replacing the door board



   
ReplyQuote
(@local-yocal)
Trusted Member
Joined: 17 years ago
Posts: 48
Topic starter  
replacing the door operator control board fixed this issue. The aux. contacts are located on door board



   
ReplyQuote
(@haroon)
Eminent Member
Joined: 17 years ago
Posts: 12
 
I am also working in KONE elevator that uses LCECPU40 board and its shows 5152 fault. I dont have its manual therefore can you tell me what is this error?



   
ReplyQuote
(@kone-d)
Trusted Member
Joined: 17 years ago
Posts: 32

   
ReplyQuote
(@haroon)
Eminent Member
Joined: 17 years ago
Posts: 12

   
ReplyQuote
Share:
Scroll to Top