Elevator Forum

Notifications
Clear all

Dover 1980’s Print

22 Posts
8 Users
0 Reactions
23.7 K Views
 M2RE
(@m2re)
Estimable Member
Joined: 17 years ago
Posts: 82
Topic starter   [#26593]
Does anyone has any manual or print similar to this Dover? There is no information about this one and I’m experiencing a lot of trouble with this Dover.
Attachments
C10CCA5C-E090-4B93-8C98-EC8F2F9E662C.jpeg (226.3 KB, 284 downloads)
70C7DACA-A0E6-499C-B079-6FD332ADB3C5.jpeg (149.51 KB, 197 downloads)



   
Quote
(@ashley)
Reputable Member
Joined: 17 years ago
Posts: 176
 
Can't tell from your pics, but it looks like the IBM relay units, but either way you can take the job number off the data tag and order prints thru vertical express that are job specific. I would order new yellow jacket relays from world electronics for it if your not familiar with maintaining the IBM relays.

What kind of problems are you having?



   
ReplyQuote
(@chainring)
Trusted Member
Joined: 17 years ago
Posts: 40
 
Those are all Potter Brumfield relays, not a Wire Contact Relay (WCR), but I’ve not seen a controller layout just like that. What year is it?

Last edited by Chainring; 04/27/19 01:07 PM.


   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759

   
ReplyQuote
 M2RE
(@m2re)
Estimable Member
Joined: 17 years ago
Posts: 82
Topic starter  
Well I’m not sure of the year of this elevator. Was looking the best with tags but dint had much luck. I found this controller tag. Might help you
Attachments
B720C510-9BFE-4E54-9820-E98D943281E1.jpeg (2.01 MB, 139 downloads)

Last edited by M2RE; 04/28/19 02:14 AM.


   
ReplyQuote
 M2RE
(@m2re)
Estimable Member
Joined: 17 years ago
Posts: 82
Topic starter  
Exactly. The IBM are in the slide door in the side. Do you guys know what type of controller is this? This is definitely an Dover but it must be an early generation, the layout is just like a composite but has a slide different since is a hydraulic. I don’t think is a composite though.



   
ReplyQuote
(@elmcannic)
Honorable Member
Joined: 17 years ago
Posts: 635

   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759

   
ReplyQuote
 M2RE
(@m2re)
Estimable Member
Joined: 17 years ago
Posts: 82

   
ReplyQuote
(@ashley)
Reputable Member
Joined: 17 years ago
Posts: 176
 
When you are working on it, remember that there are two different IBM relays on the front, you can't swap them with each other. Also when you reseat the relays, you need to make sure the bases didn't push out the back side.



   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759

   
ReplyQuote
(@eleventh-place)
Active Member
Joined: 17 years ago
Posts: 5
 
I have a Dover Elevator installed in 1980. I can't find the original "E" job number so I haven't been successful obtaining prints for it. If anyone can help I would really appreciate it. The sticker I have on the unit shows:
Dover Elevators
Equipment #777
MFG Serial # 217051
Any ideas? Perhaps someone has an "E" code from the same unit?
Thanks,
Bill



   
ReplyQuote
(@montana)
Honorable Member
Joined: 17 years ago
Posts: 515

   
ReplyQuote
(@eleventh-place)
Active Member
Joined: 17 years ago
Posts: 5
 
In investigating further the State says that it is a Westinghouse Elevator. I do see that the hydraulics are labeled Westinghouse but I was going by the sticker on the front panel that says Dover. I'm the owner of the building and not familiar with most of this. What is the "crosshead data tag" and where is it located? I have pictures of every tag on the elevator motor and controls in the elevator room.
Thanks,
Bill



   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759
 
The crosshead datatag is not accessible to you but it sounds like it’s a Dover Mod of an old Westinghouse. Your elevator maintenance company should be able to tell you what kind of controller it is.



   
ReplyQuote
Page 1 / 2
Share:
Scroll to Top