Elevator Forum

Notifications
Clear all

Tac 20

12 Posts
4 Users
0 Reactions
9,808 Views
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316
Topic starter   [#14313]
Had pipe burst in apartment last night and rain down hoistway. Door op board blew up. Is it a straight swap or is there programming involved.



   
Quote
(@magic-smoke)
Trusted Member
Joined: 17 years ago
Posts: 68

   
ReplyQuote
(@vatorgator)
Honorable Member
Joined: 17 years ago
Posts: 432
 
it depends, we have replaced a few of the door boards on tac20 and tac32 the UDC boards come with a tag on it that says caution factory test software loaded please load appropriate software or something to that affect. i have not tried it right out of the box, as i just download the generic software to the board. then down load the correct parameter list for the type of door.
i just installed a new smart tech thyssen board we bought, and it had the same caution tag on it, i did not change the software on this unit, and it worked
not sure if the UDC board will work right out of the box with factory test software, what ever that may be. maybe they are trying to make it more difficult the need be.



   
ReplyQuote
(@silly)
Estimable Member
Joined: 17 years ago
Posts: 215
 
Typically the generic UDC software is set up for AC center opening. Might have just gotten lucky vatorgator and it matched. You will need to get software for 90% of them to match the job correctly, whoever thought AC center opening was the norm is an idiot....

Process for doing it isn't horrible, let me know if you need some step by step instructions. Does the TAC 20 job have a flash drive? I think they were dumping generic door software on them for a while so that would be helpful.

Also TKE does not use the PA3 card anymore (typical for TAC 20), you will most likely get a PA6, so don't panic, they are a straight swap in that regard.



   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316
Topic starter  
Silly, i didn't notice any flash drive. Step by step instructions would be great, never replaced this board before, thank you



   
ReplyQuote
(@vatorgator)
Honorable Member
Joined: 17 years ago
Posts: 432
 
you will also need a special adapter from vertical express or a thyssen buddy that will allow you to hook up your laptop to the board and use hyper terminal to download the software.



   
ReplyQuote
(@silly)
Estimable Member
Joined: 17 years ago
Posts: 215
 
Ok peep, I will be on an inspection tomorrow that should allow me time for a precise write up, or if you like, private message me with a phone number and I can give you a ring. Hope to god you are in the US, don't wanna explain to the boss why I was calling Fiji....again...



   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316
Topic starter  
Hey silly, can you get these boards pre-programmed from vertical express? Are these door ops set up the same way as a dover. I do have access to an ims tool



   
ReplyQuote
(@silly)
Estimable Member
Joined: 17 years ago
Posts: 215
 
IMS helps, no idea about pre programming but it's worth a shot. Not sure how the DMC Dovers were set up as I was just a wee apprentice back then, and my job was simple, make my mechanic look good. Let me know if you need the help bud.



   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316

   
ReplyQuote
(@vatorgator)
Honorable Member
Joined: 17 years ago
Posts: 432

   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316
Topic starter  
Nope, just did a door scan with ims and than checked door operation with autocycle. It was just like programming the dover door op



   
ReplyQuote
Share:
Scroll to Top