Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 492 / 549 Prev Next

Otis DOB, 900 MCSS timeout

Last post by Pjf79, 4 weeks ago

Posts: 3

The lift is under installation and I am getting er...

By gilles 14 years ago
If you are installing this lift,I would assume you...

By elevatedo... 14 years ago
-you need to contact the Regional Field Engineer f...

By E311 14 years ago

Card Reader on Schindler 5300

Last post by Pjf79, 4 weeks ago

Posts: 1

Hi, there is a symbol on the glass panel of the CO...

By Pilbara 14 years ago

Otis Mrq dbf fault

Last post by Pjf79, 4 weeks ago

Posts: 4

Hey guys,the car was at the floor doors open with ...

By matt 24 14 years ago
had issues with break switch on these units, also ...

By billvator 14 years ago
dbf is caused by any contact on u or d relay and u...

By bozo 14 years ago
btw check ur contacts on ohms with ur meter

By bozo 14 years ago

EC LSSM board

Last post by Pjf79, 4 weeks ago

Posts: 1

Have a traction unit modernized in 2011. Intermitt...

By Elevatorf... 14 years ago

Doors drift open on a Dover DMC

Last post by Pjf79, 4 weeks ago

Posts: 15

Hi, we've got this side opening car, where when th...

By Vic 14 years ago
Going out with the new board today.I still think t...

By Vic 14 years ago
I have encountered this problem and the remedy, at...

By john jay 14 years ago
Funny you should mention this..had one that did th...

By Len 14 years ago
view all posts

Dirty Little Tricks

Last post by Pjf79, 4 weeks ago

Posts: 34

Just read a post between Elevatorfella and Scott D...

By jkh 14 years ago
I've now come across two I-2 Dover valves that wer...

By Indirtwet... 11 years ago
I've seen first hand nails in a traveling cable up...

By EleVADER 11 years ago
Why are contracts lost?.......poor- service,cleani...

By radar 11 years ago
view all posts

Old DMC post, anyone remember this one?

Last post by Pjf79, 4 weeks ago

Posts: 3

It's been quite awhile ago, but saw a post about s...

By Elevatorf... 14 years ago
not a resistor, it is the d4 diode, just to the up...

By Scott Dav... 14 years ago
Thanks Scott, your memory is a lot better than min...

By Elevatorf... 14 years ago

Otis 411 AC Drive

Last post by Pjf79, 4 weeks ago

Posts: 6

I'm trying to track down any AC drive information ...

By dre1383 14 years ago
e411 with a ovf428 drive would be my guess

By GreenPant... 14 years ago
Gp when you say e411 your referring to elevonic co...

By uppo72 14 years ago
The building was modded with Otis equipment in 200...

By dre1383 14 years ago
view all posts

Kone KCM 831 Disable Random Calls.

Last post by Pjf79, 4 weeks ago

Posts: 4

Long story short, i am stuck 6 hours from home try...

By CutTheRop... 14 years ago
Look in the display menu. Under test and runs. Hop...

By jkh 14 years ago
Set menu 4, submenu 21 to "0". No need to cycle po...

By SteveO 14 years ago
As above, but it should revert after power down, i...

By Dmhughes 14 years ago

Vertitiron/ Midwest Hydro

Last post by Pjf79, 4 weeks ago

Posts: 6

Anybody got any experience on this controller. I j...

By sbrmiliti... 14 years ago
Vertitron promotes themselves as NON-Proprietary. ...

By Broke_She... 14 years ago
you only need the password for the Test Operation,...

By Scott Dav... 14 years ago
Yeah thanks for the info, really good info thanks ...

By sbrmiliti... 14 years ago
view all posts

Page 492 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
26 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed