Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 400 / 549 Prev Next

Montgomery Series A

Last post by Pjf79, 3 weeks ago

Posts: 2

What causes the main contactor to buzz when the dr...

By BRG 11 years ago
the lamination's worn, or a pulshader is cracked. ...

By john jay 11 years ago

gal galaxy trouble hpv 600 drive

Last post by Pjf79, 3 weeks ago

Posts: 4

have never worked on a galaxy controller, route me...

By Vatorgato... 11 years ago
I have two galaxy hydros to look at for someone ne...

By jkh 11 years ago
If you have an HPV 600 drive that is a series II, ...

By Player1 11 years ago
JKH we fixed a jack yesterday that had been squirt...

By danzeitz 11 years ago

Prints

Last post by Pjf79, 3 weeks ago

Posts: 2

Hello,Just got back in the trade 3 months ago afte...

By Neuby777 11 years ago
PM your email address. I would be glad to help you...

By jkh 11 years ago

Kone Marathon WG door operator cable issue

Last post by Pjf79, 3 weeks ago

Posts: 5

Have a Kone hydro with this operator that seems to...

By ABE 11 years ago
It was always aircraft cable, it came from MAC Spa...

By john jay 4 years ago
Just for the fun of it, those WG door operators re...

By JJR 4 years ago
On other end is spring to keep tension on cable, i...

By chicago 4 years ago
view all posts

Rope tensioning

Last post by Pjf79, 3 weeks ago

Posts: 5

Out of curiousty, what methods do you use to check...

By beaupeep 11 years ago
I have a set of the equator that I believe I purch...

By jkh 11 years ago
Brugg makes a hydraulic rope tensioner that works ...

By Elevatorm... 11 years ago
You tune them like guitar strings... all equal. Ea...

By spanky 11 years ago
view all posts

TK Twin Post Holeless Telescopic Piston

Last post by Pjf79, 3 weeks ago

Posts: 10

hello all,I have a 2 stop hydro (TAC-20) that has ...

By bk2fla 11 years ago
look what I found!!! Attachments fau1.jpg (87.7...

By bk2fla 11 years ago
You found it! Its a fun oily journey to get there ...

By ABE 11 years ago
haha yes we had a blast!

By bk2fla 11 years ago
view all posts

kinematics Research LTD

Last post by Pjf79, 3 weeks ago

Posts: 3

Hey all! hoping someone has some insight on a 3 ph...

By JopOSopHo... 11 years ago
I would check the fuse ratings on the secondary si...

By danzeitz 11 years ago
If you sent the transformer to the motor rewinders...

By uppo72 11 years ago

OTIS CSB's lifecycle???

Last post by Pjf79, 3 weeks ago

Posts: 3

Anyone have any documentation or knowledge of the ...

By EleVADER 11 years ago
From what I know of these belts, belt life is gaug...

By jkh 11 years ago
Expect about 3 million cycles...

By Alex75 11 years ago

Otis 211 Selector

Last post by Pjf79, 3 weeks ago

Posts: 3

Received a rebuilt selector board from Unitec, dea...

By Tarth 11 years ago
Actually it may be a 100 ohm resistor.It is silk s...

By Tarth 11 years ago
Make Unitec send you a new one. What prompted you ...

By NewMech 11 years ago

Baxco bmhc-10?

Last post by Pjf79, 3 weeks ago

Posts: 4

Does anyone have a generic set of prints or owner'...

By omgitsonm... 11 years ago
Approx what year is the installation?

By ABE 11 years ago
PM me, I have some.

By iggy 11 years ago
Sorry this is old. Did you find what you were look...

By CBass 11 years ago

Page 400 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
4 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed