Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 386 / 549 Prev Next

miconic a

Last post by Pjf79, 3 weeks ago

Posts: 5

I had a IGBT explode on a miconic a's drive yester...

By Jcjphoeni... 11 years ago
Had the same thing happen, a bad INT (firing) boar...

By jj5phil 11 years ago
It's was a bad INT board. It has a locked up pulse...

By Jcjphoeni... 11 years ago
When an igbt explodes on this controller, Is there...

By Jcjphoeni... 10 years ago
view all posts

Electrical safety

Last post by Pjf79, 3 weeks ago

Posts: 4

Anyone out there using flame resistant clothing? I...

By beaupeep 11 years ago
I have a few pieces. The last thing I purchased wa...

By jkh 11 years ago
I will try not to carry on too long. ARC Flash is ...

By danzeitz 11 years ago
Dan,I can always count on you bring your "A" game ...

By jkh 11 years ago

Bucher Valve

Last post by Pjf79, 3 weeks ago

Posts: 12

We have been installing these new valves for the p...

By gandye92 11 years ago
Don't use any additive with these units as it will...

By ThyssenKr... 10 years ago
Check your gain adjustment thru IMS and valve adju...

By Johnny 10 years ago
A couple I have were Cavetating and had to add a b...

By lowoil 10 years ago
view all posts

LG Sigma

Last post by Pjf79, 3 weeks ago

Posts: 1

LG Sigma E 180 DO fault , need help , change Cpu, ...

By cucuvator 11 years ago

Miconic Mx-Gc

Last post by Pjf79, 3 weeks ago

Posts: 3

Hi guys,I am working on a reasonably new Mx-Gc mic...

By heisenber... 11 years ago
H,On the prints are you able to trace the safety c...

By jkh 11 years ago
Search for the safety-circuit in the schematics. I...

By Led zeppe... 11 years ago

DMC losing hall buttons

Last post by Pjf79, 3 weeks ago

Posts: 3

Hi, it's a DMC duplex. Occasionally the hall butto...

By gandye92 11 years ago
One car should be Master and one Slave.. if This i...

By Rolly 11 years ago
check you clc parameters car 1 is always the maste...

By Len 11 years ago

Elevator License

Last post by Pjf79, 3 weeks ago

Posts: 2

Has anyone taken the North Carolina Special Restri...

By xxXBlazeX... 11 years ago
20 years ago. I've looked into it about a year ago...

By Boa 11 years ago

Prints

Last post by Pjf79, 3 weeks ago

Posts: 3

Looking for a set of White-Evans hydro prints.

By Elev^te79 11 years ago
Is that anything like KM WHITE/ early Elevator Ele...

By elmcannic 11 years ago
I don't think so , they turned into amco then Thys...

By Elev^te79 11 years ago

OTIS 211

Last post by Pjf79, 3 weeks ago

Posts: 5

I have an Otis 211 fault code of FLRP. Does anyone...

By sec 11 years ago
Check your tape magnets for slipping. A dab of RTV...

By NewMech 11 years ago
Also check tape guides. I like those because you c...

By xxXBlazeX... 11 years ago
Thanks to all. It was the selector guides. Runs fi...

By sec 11 years ago
view all posts

Why not use mechanicle load breaks

Last post by Pjf79, 3 weeks ago

Posts: 4

Why don't elevators just use mechanical load break...

By RCD 11 years ago
i would think the obvious reason would be back las...

By jkh 11 years ago
Originally Posted By: jkh i would think the obviou...

By RCD 11 years ago
RCD,Bi-directional brakes have been around a long ...

By jkh 11 years ago

Page 386 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
0 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed