Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 330 / 549 Prev Next

Swift futura problem. Fault 94,10,9,18

Last post by Pjf79, 3 weeks ago

Posts: 5

I'm having a problem with a swift futura leaving t...

By James Dat... 9 years ago
Did you ever get to the cause of this?

By Scarz3 9 years ago
For all your CEC Swift Questions and concerns,call...

By MILTRONIC... 9 years ago
HiI have a problem with xxxx and i desperately nee...

By elmcannic 9 years ago
view all posts

Schindler mx gc Missing Node fault

Last post by Pjf79, 3 weeks ago

Posts: 4

Hi guys, been getting this issue for a while now o...

By heisenber... 9 years ago
did you freeze the nodes already/recently?-> fr...

By ktec 9 years ago
Originally Posted By: heisenberg I have the same p...

By ktec 9 years ago
I have swapped the top of car board with another l...

By heisenber... 9 years ago

Armor TMS 900

Last post by Pjf79, 3 weeks ago

Posts: 2

Car doesnt seem to have any ideal where its at, tr...

By Greg1234 9 years ago
Try Pulse counter board in computer. Did you log i...

By Rolly 9 years ago

Siemens Starter Fault

Last post by Pjf79, 3 weeks ago

Posts: 5

Getting a "Incoming Power Low Line" on the screen....

By elevatorg... 9 years ago
That would be my guess too. Not sure if the logic ...

By Indirtwet... 9 years ago
Did you measure voltage with a meter or use the St...

By CBass 9 years ago
It was the logic board. I just haven't ever seen t...

By elevatorg... 9 years ago
view all posts

Schindler Fault codes for 330a

Last post by Pjf79, 3 weeks ago

Posts: 2

Does anyone happen to have or know where I could g...

By Adamabm 9 years ago
Send me a PM with a valid email address. Email nee...

By Rolly 9 years ago

schindler 3300 dead ESM

Last post by Pjf79, 3 weeks ago

Posts: 1

have a 3300 with lightning strike. display lit but...

By mrhappy 9 years ago

US assension 1000

Last post by Pjf79, 3 weeks ago

Posts: 16

Will not hold hall call or car callsWill not run u...

By TCElevato... 9 years ago
Sounds like a plan and does anyone have access to ...

By TCElevato... 9 years ago
We would get rid of all the factory female push on...

By danzeitz 9 years ago
I replace the original Molex terminals with gold p...

By Indirtwet... 9 years ago
view all posts

Westinghouse ERL triplex.

Last post by Pjf79, 3 weeks ago

Posts: 3

I have a triplex,#2 genny is out,so down to #1 &am...

By muhs77 9 years ago
tach on end of generator coming up to voltage? Thi...

By Johnny 9 years ago
Go to the machine room. See if the gennys are cran...

By E-man 9 years ago

TAC50-04 Hall Node

Last post by Pjf79, 3 weeks ago

Posts: 16

I have a four(4) car group with two (2) risers. Th...

By MSELEVATO... 9 years ago
1. That is exactly right, terminations on CPUA and...

By Indirtwet... 9 years ago
With power off and CCH unplugged from controller y...

By Jm160 9 years ago
Well to close out the call, all four (4) 32bit pro...

By MSELEVATO... 9 years ago
view all posts

Montgomery 207E machine

Last post by Pjf79, 3 weeks ago

Posts: 2

Does anyone have a repair manual for this machine?...

By ABE 9 years ago
Mainshaft bearings going bad and letting gear bott...

By Johnny 9 years ago

Page 330 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
4 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed