Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 288 / 549 Prev Next

Montgomery 6010s

Last post by Pjf79, 3 weeks ago

Posts: 2

Having trouble with one elevator that won't cancel...

By Htx_Val 8 years ago
HCN Output has to come on, in slowdown, or if the ...

By john jay 8 years ago

Otis Blue Tool

Last post by Pjf79, 3 weeks ago

Posts: 1

Hey y’all— anybody have any info on the use of an ...

By Nashville... 8 years ago

Otis MRL

Last post by Pjf79, 3 weeks ago

Posts: 11

Elevator is stuck on safetys and cant get elvator ...

By Pockets 8 years ago
You may need the blue tool to reset the safeties p...

By Rav4guy 8 years ago
Throw the disconnect in the jam panel, put your ke...

By muhs77 8 years ago
Throw the disconnect in the jam panel, put your ke...

By muhs77 8 years ago
view all posts

Kone KCM LCECOB24 board (KM757650G11)

Last post by Pjf79, 3 weeks ago

Posts: 5

Hello,Having issues with a job randomly losing pro...

By RobM 8 years ago
Add a delay on timer in the power supply to the CP...

By Indirtwet... 8 years ago
The Chip is pulled from board and reprogramed and ...

By RobM 8 years ago
Indirt we trust is correct the inrush of power kil...

By Upndwn 8 years ago
view all posts

Schindler Miconic

Last post by Pjf79, 3 weeks ago

Posts: 4

Looking for help. Miconic HX I think. Not very fam...

By green sle... 8 years ago
Miconic HX "you think"...is it a hydro or traction...

By Tamperpru... 8 years ago
Traction elevator. Those were the only two faults....

By green sle... 8 years ago
Miconic HX (the H is for Hydro)is no HX traction 0...

By NOTIME 8 years ago

Kone Resolve 20 troublshooting manual

Last post by Pjf79, 3 weeks ago

Posts: 4

We recently took over a Kone Resolve 20 elevator. ...

By EMS-WOR 8 years ago
tell me you fault code which is occur in your lift...

By Azhar hus... 8 years ago
Trying to troubleshoot an issue with a Reynolds an...

By EMS-WOR 7 years ago
Under normal power the unit runs fine. When we tri...

By EMS-WOR 7 years ago

Kcm v3f25 intermittent 126 sub 2100 faults.

Last post by Pjf79, 3 weeks ago

Posts: 3

Car takes calls and leveling, load weighing, and t...

By Rdwarrior 8 years ago
adjusted 5-20-9 to 150 and good to go.

By Rdwarrior 8 years ago
Did you change to an adon 3 board? Then changed 5-...

By Upndwn 8 years ago

TAC 50-04 Hall Communication Problem

Last post by Pjf79, 3 weeks ago

Posts: 5

Hello looking for some insight on this one. Have a...

By travator 8 years ago
Thanks for the info. TECF does work on car 2. I wi...

By travator 8 years ago
All I/O assignments are there and all of the param...

By travator 8 years ago
Make sure your sca table is correct. W11=0. Teccr ...

By Whadafack 8 years ago
view all posts

TAC32 blowing fuse P24M

Last post by Pjf79, 3 weeks ago

Posts: 10

Good morning brothers & sisters, I have a tac3...

By omgitsonm... 8 years ago
P24m is being fed from the cop power supply so i d...

By Whadafack 8 years ago
BTW, I have now seen Con 650 used but don’t have a...

By Indirtwet... 8 years ago
Omg did you fix it? I’m having same issue. Blew tw...

By matt 24 8 years ago
view all posts

Problem with Mcs 321

Last post by Pjf79, 3 weeks ago

Posts: 4

Hello. Elevator starts up normally but does not at...

By sampler 8 years ago
Originally Posted by sampler Hello. Elevator start...

By koneislan... 8 years ago
i will try. thank you very much. best regards.

By sampler 8 years ago
I thank you very much "koneisland". We foud the pr...

By sampler 8 years ago

Page 288 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
2 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed