Elevator Forum

Otis LRV4 Hydro Dea...
 
Notifications
Clear all

Otis LRV4 Hydro Dead

18 Posts
9 Users
0 Reactions
22.6 K Views
(@gregk)
Active Member
Joined: 17 years ago
Posts: 5
Topic starter   [#4390]
Working on an Otis LRV4 ..2-stop Hydro..about 1986 vintage. We replaced the relay board, and the mcb carstation board. The elevator still wont do anything. I have the 9v, and the 30v on the carstation board. (MCB).I have two LED on board lit..but buttons, P.I. doors will not lite or move, checked all fuses. DR relay is only function that moves when power is applied. Any ideas?



   
Quote
 Len
(@len)
Estimable Member
Joined: 17 years ago
Posts: 194
 
so where is the car..below the floor..the fact that only one relay is up the (DR)only means that you have doorlocks and gate circuit good..every other relay is a 24vdc which is activated by the ground signal output from the processor,to verify if you have a problem with the processor new or not easy test if all fuses are all good safety circuit is intact...ground the pm and umv or dmv inputs at the relay shelf terminal.if car runs up or down problem is processor...



   
ReplyQuote
(@elevatedone)
Estimable Member
Joined: 17 years ago
Posts: 132
 
I have two LED on board lit.

Which two?
Do you have your inputs?

You might have the I/O sheet in the back of the prints that will tell you your inputs and outputs.
Stupid question,but you did replace the chip(s) from the old to the new board didn't you?



   
ReplyQuote
(@gregk)
Active Member
Joined: 17 years ago
Posts: 5
Topic starter  
This vintage car station board doesn't have all the little LEDs by each output or input. it only has three LEDs which is probably for voltage recognition . Think they were labeled 1,2,& 3. ( 1 &2 are lit)
I can move the car by jumping in PM starter & valve,but car will not do anything on its own. No matter where I put it in hoist way.
New board doest come with the two processor chips (U41 & U42) yes those have Ben swapped to new Board.



   
ReplyQuote
 Len
(@len)
Estimable Member
Joined: 17 years ago
Posts: 194
 
If all the dip switches are exact to original..I wouldn,t rule out the possibility of a bad replacement board, i,ve replaced 3 boards before I was able to get the car to run...you may even have a loose
wire connection or wire fell of the TB1-TB3 connect behind the cop,direction circuit intact..broken traveler..all places to check..



   
ReplyQuote
(@elevatedone)
Estimable Member
Joined: 17 years ago
Posts: 132
 
Yes bad boards are common,thats for sure.

But I wanted to add that those chips by all the inputs and outputs are "buffers" and replaceable.
Say,like you have you input coming to the board,but no output,replace that chip that corresponds to that IM or OM.



   
ReplyQuote
(@scott-davidson)
Honorable Member
Joined: 17 years ago
Posts: 402
 
first thing i would do is to check every input in the cop terminal strips that feed the processor input wiring. does the car run on inspection? if not, first input would be the ES input which is a contact off of the stop switch. this controller has 2 stop switch circuits, one in the main safety circuit, and one that only feeds the es input. the other input would be DR. this is the door circuit, if Dr relay is picked which you indicated, then a contact on dr feeds the dr input , if it is not working, then the car will not run. hopefully you have the correct print, as there are some slight variations of the input circuitry on the lrv in regard to the MB terminal strips.

Last edited by Scott Davidson; 08/17/12 02:50 AM.


   
ReplyQuote
(@gregk)
Active Member
Joined: 17 years ago
Posts: 5
Topic starter  
I have replaced the MCB board again. I have found if I plug in the om3, or om4 the bufers will heat up rapidly. Remember I have NO functions at all. I am not blowing any fuses, and all power supply are correct. The doors have no power. I have no lights when any buttons are pushed. No inspection movement. Nothing. I did find out that the building loss power to activate this. Lightning?.
I am on the track of bad software. We are looking for software now.



   
ReplyQuote
(@greenpants)
Reputable Member
Joined: 17 years ago
Posts: 276
 
car should run on inspection even without software. pretty sure it will run even without a MCB. check your relay board inputs and outputs.



   
ReplyQuote
 E311
(@e311)
Reputable Member
Joined: 17 years ago
Posts: 363
 
OM3 and OM4 are Nudge and up main valve outputs-they go through the traveler. Have you checked that your traveler is ok?



   
ReplyQuote
(@broke-sheave)
Reputable Member
Joined: 17 years ago
Posts: 418
 
On any equipment, if you wind up frying the software and you have to buy from the OEM for replacement....Go ahead and spend the few bucks, and have the OEM do the replacement and check out of the equipment.

You'd be surprised how quickly your warranty can disappear, by the time the check is written and the chip hits your hand.



   
ReplyQuote
(@charlie)
Active Member
Joined: 17 years ago
Posts: 17
 
Check all plug connections on boards you swapped. Its possible you are off on one of the plugs by a pin.... Easy to do.



   
ReplyQuote
(@elmcannic)
Honorable Member
Joined: 17 years ago
Posts: 635
 
someone above mentioned the 24 volts. if I remember right, DR is an 120volt controlled relay and the rest are 24volt. similar problem a few years back were the 24 volts was lost on the relay board itself, resulting in the exact condition Greg describes and no fuses blew either. something to do with a regulator(?) at the 24 volt source on the relay board itself. I remember we were able to bypass it until a new board could be installed. pardon my vague recollections, but maybe it'll stir some thought and investigation.



   
ReplyQuote
(@elevatedone)
Estimable Member
Joined: 17 years ago
Posts: 132
 
Yes,that 24 volt regulator can go bad and easily replaceable.
Can buy one at Radio Shack,or use to.
They just plug in.
Forgot about that one.



   
ReplyQuote
(@elmcannic)
Honorable Member
Joined: 17 years ago
Posts: 635
 
guess we'll have to wait for Greg to get back to us with the fix. it's a drag when a problem is posted, then you never hear of the solution.



   
ReplyQuote
Page 1 / 2
Share:
Scroll to Top