Elevator Forum

Notifications
Clear all

OTIS GCS

13 Posts
5 Users
0 Reactions
24.6 K Views
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10
Topic starter   [#8999]
Hey guys, new to the forum so be gentle.

I'm from over the pond In the uk and having a problem with the above lift.

We had a power cut and the drive had to be replaced. Now the fault code is showing 713 block by 702. Ive been told fault code 702 is a pre charge fault. None of my gen2 pocket manuals offer any help and we haven't got nothing in our office about these controllers. Can anyone offer any help?? Thanks.

Last edited by Jeffers; 11/16/13 05:26 PM.


   
Quote
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10
Topic starter  
Ok... Found some more info out to try and help with getting some understanding of this fault code.

The drive is a ovft02b Regen Drive.

Fault code when the test tool is plugged into the drive is 713. Which states blocked by 702. So either of those codes would be great. It's on the new gen2 regen controller.



   
ReplyQuote
(@elevated)
Trusted Member
Joined: 17 years ago
Posts: 53

   
ReplyQuote
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10

   
ReplyQuote
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10
Topic starter  
Ok the precharge fault is where the dc bus doesn't reach it's charge within a 2 second period. Anyone know how I can rectify this?? Thanks



   
ReplyQuote
(@uppo72)
Honorable Member
Joined: 17 years ago
Posts: 562
 
Originally Posted By: Jeffers
Ok the precharge fault is where the dc bus doesn't reach it's charge within a 2 second period. Anyone know how I can rectify this?? Thanks

I would think either the charging circuit, supply voltage or the caps themselves.



   
ReplyQuote
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10
Topic starter  
That's easier said then done. I've got a ovfr1a manual but I think it's slightly different.

We have a ovfr02b drive. Does anyone have a write up on this available?? Thanks.



   
ReplyQuote
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10
Topic starter  
Our drive repair guys have told ya they have had it all working. We are going to change the gdcb board Incase that's causing a fault and locking the drive out. Seems a shame that I can get a ovfr02 drive write up. If anyone knows of how I can get one that would be great!



   
ReplyQuote
(@uppo72)
Honorable Member
Joined: 17 years ago
Posts: 562
 
Originally Posted By: Jeffers
That's easier said then done. I've got a ovfr1a manual but I think it's slightly different.

We have a ovfr02b drive. Does anyone have a write up on this available?? Thanks.

Yep sure but I would think undercurrent faults would be a caps issue but have had erroneous over current faults that were the same. Not on this equipment but other types of Vf's.



   
ReplyQuote
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10
Topic starter  
Ok, we changed the GDCB and programmed it. We are now getting fault code 726. However out manual doesn't state what this means. Can anyone share some light on this for us. Thanks.



   
ReplyQuote
(@jeffers)
Active Member
Joined: 17 years ago
Posts: 10
Topic starter  
Ok, found out the gdcb board doesn't pair with the controller. So I'm back to the. 702 fault. Does anyone know how or what pulls in the mx or px relays??? Thanks.



   
ReplyQuote
(@unkindbuffalo)
Trusted Member
Joined: 17 years ago
Posts: 44

   
ReplyQuote
(@alex75)
Estimable Member
Joined: 17 years ago
Posts: 130
 
Problem is with the AC voltage supply, the voltage threshold is 80% of the actual rectified AC line voltage.
Have you measured the AC line supply voltage and entered the correct value in M3-1 (Contract) AC Main Vrms?

/Alex



   
ReplyQuote
Share:
Scroll to Top