Elevator Forum

Kone TMS 600 Showin...
 
Notifications
Clear all

Kone TMS 600 Showing Power Fail & Change Board

29 Posts
2 Users
0 Reactions
23.3 K Views
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729
 
I won't give you software that has a potential for an accident or getting someone hurt. You being a board repair facility should have an EPROM programmer and if you can read the chips, software is usually not the problem. A bad TMS 600 power supply can also cause the problem.



   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729
 
In looking at the files, the communication EPROM can possibly be a 1 meg EPROM. The newer software has a 2 meg communication chip.



   
ReplyQuote
(@khaled)
Active Member
Joined: 17 years ago
Posts: 14
Topic starter  
Originally Posted By: Rolly
I won't give you software that has a potential for an accident or getting someone hurt. You being a board repair facility should have an EPROM programmer and if you can read the chips, software is usually not the problem. A bad TMS 600 power supply can also cause the problem.

I checked the power part, it has no problem.
The software read by the programmer seemed corrupted in some parts of it(need to confirm that), that's why i needed to check from a healthy one.
I also tried the removable chips in another board and gave me the same result.
So the problem is most likely related to the software.
However, I understand your desire to provide the 100% correct software and i appreciate that, so i will wait for the reply from the guys running the whole system about the speed and the specification of the Elevator.



   
ReplyQuote
(@khaled)
Active Member
Joined: 17 years ago
Posts: 14

   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729

   
ReplyQuote
(@khaled)
Active Member
Joined: 17 years ago
Posts: 14
Topic starter  
Originally Posted By: Rolly
That's a slow car.. 200fpm max. Is it a freight car or passenger? I think I have software for a 1mps passenger job.

The car is used to carry motors and heavy tools.



   
ReplyQuote
(@khaled)
Active Member
Joined: 17 years ago
Posts: 14

   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729
 
No I don't have any 1 MPS saved but if you check board and can tell if it's communication Eprom I do have that. Try just installing the communication Eprom and see if board works.. if it does I can send that.



   
ReplyQuote
(@khaled)
Active Member
Joined: 17 years ago
Posts: 14
Topic starter  
Originally Posted By: Rolly
No I don't have any 1 MPS saved but if you check board and can tell if it's communication Eprom I do have that. Try just installing the communication Eprom and see if board works.. if it does I can send that.

One of the 2 Eprom are faulty, or maybe both of them.
If you have the Communication Eprom send it ,i will download it to a new Eprom Chip and try running it.



   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729

   
ReplyQuote
(@khaled)
Active Member
Joined: 17 years ago
Posts: 14

   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729

   
ReplyQuote
(@khaled)
Active Member
Joined: 17 years ago
Posts: 14
Topic starter  
Originally Posted By: Rolly
sent

Thank you Rolly.

To confirm
You sent me 2 files, 1 for the Communications Eprom
and the second is for the Control but for the 2mps version?
So i can't run the 2nd with the elevator, and its only for testing?



   
ReplyQuote
(@rolly)
Honorable Member
Joined: 17 years ago
Posts: 729

   
ReplyQuote
Page 2 / 2
Share:
Scroll to Top