Elevator Forum

Tach 50 fault code ...
 
Notifications
Clear all

Tach 50 fault code 658

12 Posts
7 Users
0 Reactions
13.9 K Views
(@steven)
New Member
Joined: 17 years ago
Posts: 2
Topic starter   [#8453]
Besides the obvious choices, any ideas?
Have swapped the regulator card, checked the LEMS, checked the motor coils, replaced the main contractor, checked the IGBTs, swapped the DSP and CPU cards, etc.
this one is whipping me. Help?!!



   
Quote
(@sbrmilitia)
Honorable Member
Joined: 17 years ago
Posts: 448

   
ReplyQuote
(@e-man)
Honorable Member
Joined: 17 years ago
Posts: 480
 
658 Fault is not in the TAC50 manual that I've seen, it goes from 657 to 700. Maybe if you have IMS you can enter the code and ask what it is?



   
ReplyQuote
(@gs264)
Trusted Member
Joined: 17 years ago
Posts: 52
 
658 =Motor Connection error�The current regulator failed to achieve regulation in at least one of the AC motor
phase or the DC armature in one second after startup. At the start of each run, the drive will test the current
regulation to verify that themotor is connected properly. Drops Safety string via WDPF. Will not close Safety
string until given a manual reset request from the CPU or a DSP card reset. Red LED on DSP card will be
on solid.
S Open Motor Phase
S Faulty Contactor
S Field Wiring



   
ReplyQuote
(@sbrmilitia)
Honorable Member
Joined: 17 years ago
Posts: 448

   
ReplyQuote
(@steven)
New Member
Joined: 17 years ago
Posts: 2
Topic starter  
The motor has been checked, the current regulator board has been swapped, and the starter has been replaced. All IGBT's have been checked. This problem started when a coworker swapped CPU and DSP boards. I don't know if he correctly changed the chips as he did it.



   
ReplyQuote
(@sbrmilitia)
Honorable Member
Joined: 17 years ago
Posts: 448
 
Do you have the old boards where you can swap the chips? To rule out that possibility.

Another question what was the car doing before that led you to change the DSP and the CPU

Last edited by sbrmilitia; 09/14/13 02:40 AM.


   
ReplyQuote
(@sp-kette22)
New Member
Joined: 17 years ago
Posts: 1
 
Im new to this forum i was wondring if you can point me in the right direction i am troubleshootin a cab in a casino that continues to go offline several techs have been out to look with no solutions the display says EH ?



   
ReplyQuote
 jkh
(@jkh)
Prominent Member
Joined: 17 years ago
Posts: 904
 
Sp@kette22,
Who's the manufacturer?
What model?
What year was it installed?
And most importantly are you a elevator mechanic?



   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798

   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
If the Lingo isn't right or the question isn't phrased correctly we shouldn't give advice. I don't mean just badly written because English isn't the first language. We can tell amateurs from professionals.



   
ReplyQuote
(@sbrmilitia)
Honorable Member
Joined: 17 years ago
Posts: 448
 
after the run I made on that blackjack table I doubt that casino has enough money to pay for proper maintenance contract. they should have enough install all new elevators. can anyone give me a loan I need gas money to make it to work........



   
ReplyQuote
Share:
Scroll to Top