Elevator Forum

schindler hall stat...
 
Notifications
Clear all

schindler hall stations

13 Posts
8 Users
0 Reactions
21.4 K Views
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316
Topic starter   [#2257]
have problems with schindler pushbuttons on hall station, they just stop working. disconnect cable and check connection but it doesn't solve anything. button all of a sudden starts working again. anyone else have this problem?



   
Quote
(@selfproclaimed)
Trusted Member
Joined: 17 years ago
Posts: 52
 
Are they the micro switch type? If so change it. They often "click" but if you check it with a meter there is no continuity across the contacts inside the switch.



   
ReplyQuote
(@j-sand)
Estimable Member
Joined: 17 years ago
Posts: 100
 
Most of the issues (car and hall com issues and lockups) I have had are because of the excess flat satin cable bundled up in the hoistway troughing. Shorten it up and add a new end and problem usually solved.



   
ReplyQuote
(@halfpick)
Reputable Member
Joined: 17 years ago
Posts: 239
 
What series of equipment. Most related problems are from software. Current versions tried to fix problem. I have heard since I left that they are still having problems. It was real bad with the 400A product line.



   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316

   
ReplyQuote
(@cassowary)
New Member
Joined: 17 years ago
Posts: 3

   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316

   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316

   
ReplyQuote
(@philly)
Reputable Member
Joined: 17 years ago
Posts: 256
 
S3 resets the lon network. If you find the call light on or non-responsive and the microswitch is good, then the node is bad, order a new board. They are susceptible to noise interference from the 120vac in the gutter. You can easily run new shielded cat 5 and problem will disappear. That crappy flat phone cable is junk and most times the ends aren't properly installed. That's just likely your intermittent issue, just a loose connection. And cat 5 tools and ends are available at home depot.



   
ReplyQuote
(@beaupeep)
Honorable Member
Joined: 17 years ago
Posts: 316
Topic starter  
Replaced all cable ends. Still getting same issue. Only get problem when there's a hockey or lacross tournament. Figured they were bashing button. Can that cause problem



   
ReplyQuote
(@e-man)
Honorable Member
Joined: 17 years ago
Posts: 480

   
ReplyQuote
(@sec-reject)
Eminent Member
Joined: 17 years ago
Posts: 35
 
This is not a cable issue, crimping problem, etc.

This is a problem Schindler has been experiencing with all of their LON based hall call boards. Products it is seen on are 321A, 330A, and 400A.

Schindler has had several revisions of board to fix the problem, as well as the 'foil' stickers to be placed on the Echelon chip, and even replacing the standard CAT5 with a more highly shielded type.

Nothing has completely fixed the problem, and some people have suggested it began when Schindler bought the rights to produce the Echelon chip and began making their own, more cost-effective type.

I know of several customers Schindler has that are beyond angry about this.



   
ReplyQuote
(@philly)
Reputable Member
Joined: 17 years ago
Posts: 256
 
I'd offer them an upgrade to tamper proof, energy efficient conventional buttons. Stress the LED longevity and cost savings. Easy sell. Give me their info and I'll sell it for you for 20% commission.



   
ReplyQuote
Share:
Scroll to Top