Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 354 / 549 Prev Next

TAC50-04. Door Comm Loss

Last post by Pjf79, 3 weeks ago

Posts: 4

I have a TAC50 that randomly shuts down on a Door ...

By MSELEVATO... 10 years ago
Make sure the door software is V2R23, comm is plug...

By Indirtwet... 10 years ago
Well my door operator software is V2R11( but it ca...

By MSELEVATO... 10 years ago
What was the end result with this issue?

By Local8Ele... 2 years ago

Dover DMC 1 F2 Fuse Type

Last post by Pjf79, 3 weeks ago

Posts: 1

Hello All,Does anybody know if the 4A F2 Fuse on a...

By Opamp Ott... 10 years ago

Glass door for vertical platform lift/wheelchair

Last post by Pjf79, 3 weeks ago

Posts: 3

We are in the process of ordering an Ameriglide ve...

By vatorboy 10 years ago
Have you asked any cab manufactures?ColumbiaEDI/EC...

By jkh 10 years ago
Thanks so much, JKH! I haven't checked these compa...

By vatorboy 10 years ago

400a

Last post by Pjf79, 3 weeks ago

Posts: 4

Does anyone know what error drive 148 safety t4 on...

By Jcjphoeni... 10 years ago
Either gates or doors,look on the print and see wh...

By lowoil 10 years ago
T4= the 4th SKD in the safe circuit. Usually a doo...

By E-man 10 years ago
Thanks for the info. They are eci locks on a parki...

By Jcjphoeni... 10 years ago

destination dispatch

Last post by Pjf79, 3 weeks ago

Posts: 1

I've got 2 four banks , tac 50-04's, with destinat...

By Jcjphoeni... 10 years ago

TAC-20

Last post by Pjf79, 3 weeks ago

Posts: 4

Car fault 1062 encoder interrupt failure. Car pass...

By Up and do... 10 years ago
What's your p17 and p18?did you check slow down ma...

By lowoil 10 years ago
Does it happen in the same spot every time ?

By Jluff 10 years ago
This is basically NTS. It saw the terminal slowdow...

By Indirtwet... 10 years ago

Otis door problem

Last post by Pjf79, 3 weeks ago

Posts: 9

Working on an Otis gama D or spec (not sure which)...

By Jluff 10 years ago
Txs for all your advice. I went over everything th...

By Jluff 10 years ago
Have you looked at the open and close relays/conta...

By LA Tech 10 years ago
If the problem went away after touching everything...

By Indirtwet... 10 years ago
view all posts

Ascension 1000

Last post by Pjf79, 3 weeks ago

Posts: 12

Anybody know what fires the doz led on the monitor...

By Johnny 10 years ago
I've replaced the molex on the power supply due to...

By Johnny 10 years ago
More than half the problems I've had on 1000's hav...

By Indirtwet... 10 years ago
It's been a while, but we used to solder a wire fr...

By elmcannic 10 years ago
view all posts

MRL preference

Last post by Pjf79, 3 weeks ago

Posts: 14

Need opinions. Have a customer that is renovating ...

By Boa 10 years ago
You should try to talk to builder out of mrl. I ha...

By Bowtiedro... 1 year ago
We have done a couple of MX10 and 20 replacements ...

By elevatorm... 1 year ago
I have some Smartrise C4 controllers on Schindler ...

By OH boy 1 year ago
view all posts

DMC1 issue

Last post by Pjf79, 3 weeks ago

Posts: 23

Got a 2-stop front opening only DMC1 with a select...

By Dandroid 10 years ago
Well, crap. The sucker ran fine for over a month, ...

By Dandroid 10 years ago
not sure if you know, the DZR switch is not part o...

By Vatorgato... 10 years ago
did you change the door zone reed switch?

By Vatorgato... 10 years ago
view all posts

Page 354 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
3 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed