Notifications

Clear all

Technical Questions

This is where you can ask a technical question about any equipment you are working on.

RSS

Page 323 / 549 Prev Next

Otis 211 giving FLRP fault

Last post by Pjf79, 3 weeks ago

Posts: 11

Working on an Otis 211 which keeps giving me FLRP ...

By Weupnow 9 years ago
Transition is ok, just car overshoots floors in up...

By Weupnow 9 years ago
Can you watch on the service tool or a PI that the...

By Indirtwet... 9 years ago
Two things:1) If the unit is over shooting in the ...

By elmcannic 9 years ago
view all posts

TMS600

Last post by Pjf79, 3 weeks ago

Posts: 16

Hello,We are having problem learning floors on a 1...

By Elevator ... 9 years ago
Or a pilot relay.. also make sure the brake switch...

By Rolly 9 years ago
It happens after about 5 min of idle time. A relay...

By Elevator ... 9 years ago
That sure sounds like car being held at zero speed...

By Rolly 9 years ago
view all posts

TAC 20 Linear PA6 door operator

Last post by Pjf79, 3 weeks ago

Posts: 15

Anyone had any luck recently upgrading from a PA_ ...

By Dandroid 9 years ago
Update on this. I just found out that the V2R24 ge...

By Indirtwet... 9 years ago
Too fucking complicated for a damn door operator. ...

By E-man 9 years ago
This makes sense of what we were seeing. Thanks.I ...

By Dandroid 9 years ago
view all posts

TAC 50.04 MRL UCA3 Fault

Last post by Pjf79, 3 weeks ago

Posts: 6

Hey guys, stepped into this job as a favor. New 20...

By MikeF 9 years ago
If the battery is dead it will fault out the uca3 ...

By Jm160 9 years ago
There is a board in the battery that also can go b...

By Silly 9 years ago
replace the batteries

By Whadafack 9 years ago
view all posts

I-Motion Door Operator

Last post by Pjf79, 3 weeks ago

Posts: 5

I have read a few post on here that talk about whe...

By Greg1234 9 years ago
I just replaced an imotion board about a month or ...

By Jluff 9 years ago
I’m having trouble getting an I motion 2 operator ...

By Ken P 9 years ago
I thought there was a jumper you had to move.

By Rolly 9 years ago
view all posts

Tach failure only in one direction?

Last post by Pjf79, 3 weeks ago

Posts: 2

hey guys, working on a millar cvt with dc/dc gener...

By Daniel718 9 years ago
If memory serves me correct CVT cars have an Up an...

By UpandDown... 9 years ago

Westinghouse ERL

Last post by Pjf79, 3 weeks ago

Posts: 3

Any body know what a Westinghouse ERL used as the ...

By Upndwn 9 years ago
Usually works for everything.2.5 sec for car stop ...

By Rolly 9 years ago
Thx brother . Little lag in response

By Upndwn 9 years ago

Miprom 21 loosing floor counts

Last post by Pjf79, 3 weeks ago

Posts: 8

Have a 6 car group and every week or so one of the...

By CinciElev... 9 years ago
That's a valid point, this issue didn't arise unti...

By CinciElev... 9 years ago
Problem was relay pilot board. Thought I'd put sol...

By CinciElev... 9 years ago
Thank you for posting the fix! Too many threads he...

By InFritzWe... 9 years ago
view all posts

Any CET's on here?

Last post by Pjf79, 3 weeks ago

Posts: 4

Hi all , I have journeyman certification through t...

By JimboNJ 9 years ago
I was a CET-s but let it drop

By Boa 9 years ago
I have both CET and union certs. I think it depend...

By micmerci 9 years ago
Thanks for the replies , I'm in nj were CET isn't ...

By JimboNJ 9 years ago

Otis pulse

Last post by Pjf79, 3 weeks ago

Posts: 15

Hi guys. Is there any way to bypass the pulse belt...

By Jluff 9 years ago
...................yes there is a way..but it is n...

By Len 9 years ago
[b][/b]Hey dear, May anybody share electrical draw...

By Azhar hus... 9 years ago
These belts will breakdown if not tracking properl...

By Peter iue... 9 years ago
view all posts

Page 323 / 549 Prev Next

14 Forums
7,386 Topics
41 K Posts
17 Online
2,871 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed