Elevator Forum

Notifications
Clear all

KONE miprom- HS.

17 Posts
5 Users
0 Reactions
12.9 K Views
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter   [#37511]
Hi

Got an older KONE miprom hs losing car and hoist way LON intermittently. It’s a 2 stop. Seems to only happen at 2nd floor. CPU does not show any faults but car does not respond. Any ideas what causes this ?



   
Quote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
I would check connections on the shifter board, look at the the 24vdc, and net connections. plug the Molex connectors in and out. Also gateway and Floor control boards.



   
ReplyQuote
(@project-elevator)
Trusted Member
Joined: 17 years ago
Posts: 49

   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter  
It does happen only on 2nd floor so far. It’s a 2 stop. Customer wants to replace things even though it hasn’t happened again yet besides twice in a 2 week period . Where do I find the shifter board and floor control boards ?

Last edited by Jluff; 06/09/24 11:59 AM.


   
ReplyQuote
(@montana)
Honorable Member
Joined: 17 years ago
Posts: 515

   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776

   
ReplyQuote
(@indirtwetrust)
Noble Member
Joined: 17 years ago
Posts: 1759
 
The shifter board is the big one in the controller. FCBs are the floor control boards for the hall fixtures so should be in the gutter or a box in the hoistway at each floor.



   
ReplyQuote
(@montana)
Honorable Member
Joined: 17 years ago
Posts: 515

   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter  
Is the shifter board and FCBs drop in replacements? Do they require any interaction with a service tool for set up ?

Last edited by Jluff; 06/10/24 11:41 PM.


   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
The Shifter Bd. is plug-and-play. the FCB Bd. is jumpers for the floor, and used for the Arrival gong, and Door side. The Gateway Bd. is for Duplexing. Does the CPU show the LON Net as off? If you have a Duplex the Gateway LED # L1 shows the LON chip towards the CPU as working properly and # L3 towards the other elevator working properly if they are green. Also the CPU has an LED for the Car LON and an LED for the Hoistway LON, which one is off?



   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776

   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776

   
ReplyQuote
(@john-jay)
Prominent Member
Joined: 17 years ago
Posts: 798
 
Yes a large board in the controller, it has 10 or 11 Molex connectors on the bottom, the part number used to be P-31888-001. Don't know if that is still relevant.



   
ReplyQuote
(@project-elevator)
Trusted Member
Joined: 17 years ago
Posts: 49
 
Firstly try to do the Shaft Setup by 5-2-1
Then try the LON download by 5-7-1
And clear the error with E-2-1
Power Down and ON



   
ReplyQuote
(@jluff)
Noble Member
Joined: 17 years ago
Posts: 776
Topic starter  
Ok thank you. When it happens it doesn’t throw a fault. But both Lon leds go out and the car is non responsive .



   
ReplyQuote
Page 1 / 2
Share:
Scroll to Top